6
7
8
2
1
3
4
5
Pièce
Qté
1.
Base . . . . . . . . . . . . . . . . . . . 1
2.
Roulettes . . . . . . . . . . . . . . . . 5
3.
Vérin pneumatique . . . . . . . . 1
4.
Soufflet . . . . . . . . . . . . . . . . . 1
5.
Plaque du siège. . . . . . . . . . . 1
6.
Coussin du siège. . . . . . . . . . 1
7.
Coussin extérieur du dossier 1
8.
Coussin intérieur du dossier . 1
9.
Vis 1
1
/
8
po. . . . . . . . . . . . . . . 2
10.
Vis 1
1
/
4
po. . . . . . . . . . . . . . 4
11.
Rondelles plates . . . . . . . . . 6
12.
Clé Allen (non montrée). . . . 1
9,11
9,11
10,11
10,11
10,11
ÉTAPE 1
Enlever toutes les pièces du carton, les organiser selon les numéros de
pièce indiqués sur la liste et s’assurer que les quantités des pièces reçues sont correctes.
ÉTAPE 2
Insérer les roulettes (2) dans la base (1). S’assurer que toutes les roulettes
sont insérées correctement.
ÉTAPE 3
Mettre la base (1) debout de manière que les roulettes (2) soient sur le
plancher. Insérer le vérin pneumatique (3) dans la base (1) et glisser le soufflet (4) sur l’arbre du vérin.
ÉTAPE 4
Attacher la plaque du siège réglable (5) au coussin du siège (6) avec la flèche orientée vers l’avant de la chaise en utilisant quatre vis 1
1/4 po (10) et quatre rondelles plates (11).
ÉTAPE 5
Glisser le coussin extérieur du dossier (7) sur les supports du coussin du siège (6) en s’assurant qu’il est inséré correctement. À
l’aide de deux vis 1 1/8 po (9) et de deux rondelles plates (11), attacher le coussin extérieur du dossier (7) au coussin du siège (6).
RESSERRER
COMPLÈTEMENT TOUTES LES VIS.
ÉTAPE 6
Attacher le velcro du coussin intérieur du dossier (8) avec le côté marqué «UP» vers le haut au velcro du coussin extérieur du dossier
(7).
RESSERRER COMPLÈTEMENT TOUTES LES VIS ET APPUYER LE COUSSIN CONTRE LE VELCRO.
ÉTAPE 7
Placer le siège assemblé sur le dessus du vérin pneumatique (3) et pousser vers le bas.
ATTENTION: AVANT D’UTILISER LA CHAISE, S’ASSURER D’AVOIR RESSERRÉ COMPLÈTEMENT
TOUTES LES VIS.
TEX228 CHAISE PRÉSIDENT TRADITIONNELLE
INSTRUCTIONS DE MONTAGE
© Office Star Products December 2002
TEX228 TRADITIONAL EXECUTIVE CHAIR
OPERATING INSTRUCTIONS
1
2
FEATURE
• HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and lift lever
(1). To lower seat height sit on chair and lift lever (1).
• LOCKING TILT ADJUSTMENT
For individual comfort, this chair has been equipped
with an adjustment that will allow the user to change
the tension of the tilting feature. Turn knob (2)
clockwise to increase tension and counter-clockwise
to decrease or ease the tension. To lock return chair
to the upright position and push lever (1) in. To unlock
pull lever (1) out.
NOTE:
Be careful not to loosen back tilt adjustment knob
completely.
WARNING
1. Use this product only one person at a time.
2. Do not use this chair unless all bolts screws and
knobs are securely tightened.
3. Check that all bolts screws and knobs are tight every
six months or as needed.
4. Do not overturn back tilt knob when decreasing
tension.
5. Dispose of packing material properly. Do not
use plastic cover as head covering. It may cause
suffocation.
6. Do not use chair as a stepladder.
7. Use this chair for its intended purpose only.
8. Use mild detergent only for cleaning.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts are damaged or
missing. Our customer Service Department will do everything possible to promptly remedy the problem.
TOLL FREE PARTS NUMBER
1-800-950-7262, Fax 1-909-930-5629
Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time or e-mail: [email protected]. P.O. Box 3520
Ontario, California 91761
Warranty
5 Year limited warranty on all non moving metal parts.
Seat plate, pneumatic cylinder, wood, plastic parts, base
and casters for 2 years. We can not warrant vinyl against
routine scratching and scuffing, as all vinyl is subject to
minor blemishes in use.
To make a warranty claim, contact Customer Service. Provide
model number and description of the problem. At its option
Office Star Products will: (a.) Supply compatible components of
current manufacture. (b.) Repair the customer’s component. The
customer must prepay freight on any components returned to
the factory. Return freight on components still in warranty will be
paid by Office Star Products.
All warranties are limited to the original purchaser for normal
commercial usage defined as a standard forty hour work week
by persons weighing 250 lbs. or less.