background image

 

20

 

10.

 

 Cleaning instructions

 

 

Cleaning and disinfection procedure have to be performed by qualified personnel. 

 

Use appropriate eye/facial protection and protective gloves, during cleaning and 

disinfection procedure. 

 

In case of contamination with blood or body fluids, the wheelchair has to be cleaned first and 

then disinfected as follows: 

 

Note:  Most of the time it is convenient and more effective to remove the seat and back-rest 

upholstery from the frame before proceeding with the cleaning and disinfection of either the 

frame or the upholstery. 

 

FRAME 

 

wash the wheelchair with tepid water and neutral detergent using a damp cloth to remove 

gross soiling; 

 

 wash again the wheelchair using just tepid water to remove detergent residuals; 

 

dry the wheelchair prior to further processing; 

 

visually inspect the cleanliness of the complete device; 

 

disinfect the wheelchair using alcohol (70-90%); 

 

be sure it is completely dry before proceeding with any other operation. 

 

UPHOLSTERY 

In case of no user change during the cleaning treatment: 

 

wash, rinse, dry and disinfect the upholstery using the same process used for the frame; 

 

be sure the upholstery is completely dry before to re-assembly it again to the frame.  

 

In case of different user after the cleaning treatment: 

 

in this case it is suggested to change seat and back-rest upholsteries with a new set. 

 

Note:

 during this cleaning process the wheelchair should be carefully inspected also for 

damage, oxidation and faults in function. If any damage or faults are found, the involved 

components should be removed for service, repair or replacement. 

 

All waste materials related to this process must be disposed in compliance with 

specific local applicable law.    

 

 

 

 

 

Summary of Contents for IDRA 2.0
























Reviews: