background image

 11 
 

The engine is additionally equipped with a recoil starter for 
emergency, in case e.g. the battery trips, which must be used as 
follows (devices to be handled as described before:  

 

Start procedure reverse start 

  Turn ignition key clockwise into position "1". 

  Take handle and carefully pull out until engagement, then strongly 

 

pull out in order to start motor. Put handle back into initial position.  

 

If the engine in operational state and at correct oil level does not start 
after several attempts, most likely the oil pressure is poor. In this case 
disconnect the cable of oil pressure switch (at the male threaded flange 
of the engine oil filter) upon start-up. 

 

As soon as the engine has started, cable of oil pressure switch to 
be reconnected, as otherwise the low oil level cut-out is disabled. 

 
Pressure/Flow Regulation  

Pressure and flow rate can continuously be adjusted as required at the hand 
wheel of the safety control valve. 

 
Counter-clockwise:

 

continuous pressure and flow reduction to minimum 
capacity 

Clockwise:

 

continuous pressure and flow increase to maximum 
capacity 

 

When pistol is closed, machine is running in circulation mode. If 
water temperature exceeds 60 °C, thermo valve (14) opens, 
releases small amounts of hot water and cold water enters. 

 
After Work 

In order to reduce motor stressing, decrease working pressure by turning the 
hand wheel of the safety/control valve (3). 

 

  Close and lock spray pistol. 

  Stop motor: Turn ignition key into position “0”. 

  Remove key in case machine is not in operation  

or 

unattended or remains unattended. 

  Thoroughly clean high pressure hose. In case of damage (cuts, 

abrasions, kinks) replace high pressure hose for safety reasons. 

  Only original OERTZEN high pressure hoses to be used. 

Otherwise Declaration of Conformity and warranty will expire. 

  Reel up high pressure hose properly without any loops. 

  Store machine and accessories in a dry, frost-protected area. 

  Drain pump completely in case of extended shut-down periods. 

  Drain pump in case of extended shut-down periods. 

 

Particularly note: 

In case of malfunctions, eliminate cause according to chapter „Trouble 
Shooting“, call qualified service. 
 
In case frost is likely, frost protection to be carried out (see chapter 
„Maintenance and Care“), otherwise severe damage will be the result. 

5. 

Maintenance and Care

 

 

 

 

 

 

 

 

 

Summary of Contents for M 400

















Reviews: