background image

12

Operating Instructions and Parts Manual 

24497

14" CHOP SAW

1/17

2017 OEMTOOLS

®

OEMTOOLS

®

 ONE YEAR WARRANTY

If for up to one year from the date of purchase of this OEMTOOLS

®

 product you find any defect in material 

or workmanship, through normal usage, return it to the place of purchase, or to OEMTOOLS

®

 for repair 

or replacement at our discretion. In order to obtain this service, send your tool and proof of purchase, 

transportation pre-paid, to OEMTOOLS

®

 Q.A. Dept., 3580 E. Raines Road #3, Memphis, TN 38118. We will not 

be responsible for lost or damaged goods during transportation; please insure your package. If our inspection 

verifies the defect, we will either repair or replace the product at our election, or we may elect to refund the 

purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products 

at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the 

scope of our warranty, then you must bear the cost of returning the product.
OEMTOOLS

®

 does not provide warranty for products labeled other than OEM

®

 or OEMTOOLS

®

. OEMTOOLS

®

 

will not provide any warranty for products subjected to abnormal use. Abnormal use includes, but is not limited 

to, abuse, accident, alteration, neglect, and unauthorized or unreasonable use or repairs. This warranty does not 

cover bits, blades, files, batteries, or calibration. We recommend that you maintain your tools and sharpen or 

replace blades, bits, files, and batteries as necessary. OEMTOOLS

®

 reserves the right to makes any changes in 

construction or design at any time without any obligation in incorporating such changes to tools or equipment 

previously sold.
OEMTOOLS

®

 makes every effort to ensure that its products meet high quality and durability standards, and 

warrants to the original purchaser that this product is free from defects in materials and workmanship for the 

period of one year from the date of purchase. This warranty does not apply to damage due directly or indirectly 

to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper 

installation, normal wear and tear or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or 

consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation 

of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS 

WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE 

WARRANTIES OF MERCHANTABILITY AND FITNESS. This warranty gives you specific legal rights, and you may 

also have other rights, which vary from state to state.

CONTACT US

3580 E. Raines Road, Suite 3, Memphis, TN 38118

Tel: 1-866-458-2472

www.oem-tools.com

Don’t forget to register your new OEMTOOLS

®

 product at www.oem-tools.com.

Summary of Contents for 24497













Reviews: