IN
ST
A
LL
A
TI
O
N
G
U
ID
E
La
nd
sc
ap
e
Sp
ea
ke
rs
page 1 of 2
Install Guide
Rev. A
INTRODUCTION
Congratulations on the purchase of the ST-6 speaker. The
ST-6 has been specially tuned for outdoor use and sounds
best in the outdoor environment. Since the ST-6 has a
built-in transformer it is ideally suited for use in commercial
70V/100V distributed audio systems in addition to consumer
applications with amplifiers that are designed to drive 8-ohm
loads. With its 360 degree high fidelity dispersion, the ST-6
creates a rich enveloping listening environment when used in
multiples.
CONTENTS
(1) ST-6 High Performance Landscape Speaker
(2) Security Brackets
(2) 8mm X 10mm Socket Head Screws
(Requires 6mm Hex wrench)
ADDITIONAL TOOLS & ACCESSORIES THAT
MAY BE REQUIRED
Wire cutter / stripper
6mm Hex Wrench (Allen Wrench)
(2) Waterproof wire connectors / Silicone filled wire nuts
2-Conductor direct-burial stranded speaker cable
SHIPPING DAMAGE
Each speaker is thoroughly tested before it leaves the
factory. However, in shipment, accidents may occur. Please
inspect your speakers carefully when you receive them to
make sure there is no damage. If there is, please notify your
dealer or supplier immediately for assistance. If you received
your speakers by public transportation, report the damage at
once to the shipping company.
ATTACHING SECURITY
BRACkETS
Should you wish to restrict
movement and/or theft
of the ST-6, two security
brackets are supplied with
each speaker to anchor the
speaker into the ground.
1.
Place the speaker
upside down on
surface that will
not damage the top
surface.
2.
Install the brackets as shown in the image using the
supplied hardware.
3.
Repeat for the 2nd bracket.
CONNECTION & SETUP
Connection from the speaker to the amplifier should be made
with appropriate size cable. Use the chart below to help
determine the best wire size. The cable should be rated for direct
burial applications. Landscape lighting wire often meets these
requirements.
Use waterproof wire connectors for all exterior connections.
These connectors usually contain a silicone gel to prevent
moisture ingression. This type of connector is commonly used for
landscape lighting.
Connect the short cable that is protruding from the bottom of the
speaker to the direct-burial trunk line. Prepare the connections
by stripping a short length of insulation from the ends of each
wire, exposing approximately 5/8” (15mm) of each conductor, or
perform the connections as directed by the manufacturer of the
wire connectors. Ensure that the proper polarity is maintained for
all connections. This will ensure maximum system performance.
Refer to the diagram on the next page.
Set the transformer tap position to the desired level. When using
multiple speakers on a single line in distributed 70V/100V audio
systems, the sum of the power taps selected on all the speakers
should approximately equal, but not exceed, the amplifier’s power
output. E.g. 24 speakers each set to 8 watts, 24 x 8W=192W,
therefore the amplifier should have an approximate power rating
of 200W or be limited to approximately 200W output.
Note:
Not all speakers need to be set to the same position.
Overdriving the transformer will cause saturation, distortion, and
eventual failure. Setting a high-pass filter at approximately 60Hz will
help reduce saturation of the transformer.
Exterior
ST-6 :
6-1/2" In-Ground Landscape Speaker
RECOMMENDED MAxIMUM CABLE LENGTH CHART (Based on 1dB maximum loss)
Wire Size
8-ohm
70V with 100W Load
70V with 200W Load
100V with 200W Load
#20AWG
Up to 50ft (15m)
Up to 300ft (91m)
Up to 150ft (45m)
Up to 300ft (91m)
#18AWG
Up to 80ft (24m)
Up to 425ft (130m)
Up to 212ft (65m)
Up to 425ft (130m)
#16AWG
Up to 120ft (37m)
Up to 750ft (240m)
Up to 375ft (120m)
Up to 750ft (240m)
#14AWG
Up to 200ft (61m)
Up to 1200ft (370m)
Up to 600ft (180m)
Up to 1200ft (370m)
#12AWG
Up to 300ft (91m)
Up to 1900ft (580m)
Up to 950ft (290m)
Up to 1900ft (580m)
