OEM PCA-20 User Manual Download Page 3

 

 

Warnings  

 

 

Warning!

 The equipment is CLASS I ME EQUIPMENT. 

To avoid the risk of electrical shock, the equipment must be  

protectively grounded.

 

 

 

Warning!

 The equipment should only be used inside the medical 

equipment, which has means to isolate its circuits electrically from the 

supply mains on all poles simultaneously.

 

 

 

Warning!

 Do not open the enclosure. There are no user-serviceable 

parts inside the device. Only authorized personnel is allowed to open 

the device.

 

 

 

Warning!

 The equipment is not suitable for use in presence of a 

flammable anesthetic mixture with air or with oxygen or nitrous oxide.

 

 

Explanation of symbols  

 

 

Symbol 

Description 

 

Refer to instruction manual before handling 

IPX0

 

Particles: No data available to specify a protection rating 

Water: Non-protected 

 

Warning, electricity 

 

Protective earth terminal 

 

The product should not be disposed of with household waste 

 

Manufacturing year and month 

 

Manufacturer’s name and address 

INPUT 

AC power input of the device 

HV OUTPUT 

Output positive and output negative of the device 

INTERFACE 

Interface (control) connector of the device  

 

 

Summary of Contents for PCA-20















Reviews: