3
Operating Instructions and Parts Manual
24790
5/20
2020 OEMTOOLS
®
1,100 LB. 2 STAGE TELESCOPING
TRANSMISSION JACK
31. This equipment is intended only for professional use by
personnel trained in performing the service functions
for which it is designed.
32. This equipment is designed for servicing a variety
of vehicles in a safe, convenient manner. However,
differences in vehicle makes and models may make it
impossible to use this equipment as it is intended. DO
NOT attempt to force the use of this equipment on an
application for which it is not designed to perform.
33. The procedures documented in this manual are to
serve as guidelines for the use of this equipment.
34. In addition to these guidelines, always follow the
manufacturer’s recommended procedures when
servicing each unique vehicle.
35. The use of this equipment is simple and straightforward
if you follow the instructions. When operating this
equipment, use common sense, and always stop to
think before using a Transmission Jack or lifting a
vehicle.
PRODUCT DESCRIPTION
The 1,100 Lb. 2 Stage Telescoping Transmission Jack
is designed to be used as an aid in the removal and
installation of automotive and light truck transmissions,
transfer cases and transaxles. This telescopic style
Transmission Jack is for use under an overhead lift or in a
garage pit.
PRODUCT SPECIFICATIONS
Weight Capacity 1,100 Lb.
Lift Range
37" - 76.4"
SPECIFIC SAFETY INSTRUCTIONS
AND WARNINGS
WARNING
: NEVER use for any purpose other than
those uses outlined above!
1. Verify that the product and application are compatible;
if in doubt, call OEMTOOLS
®
at 1-866-458-2472.
2. Before using this product, read the operator’s manual
completely and familiarize yourself thoroughly with
the product and its components, and recognize the
hazards associated with its use.
3. Wear appropriate safety gear (including heavy duty
work gloves and ANSI-approved safety goggles) during
use.
4. Ensure the Transmission Jack rolls freely. Raise and
lower the unloaded Transmission Jack throughout the
lifting range before putting into service to ensure the
pump operates smoothly. Replace worn or damaged
parts.
5. DO NOT exceed the weight capacity of the
Transmission Jack. Make sure weight is evenly
distributed. Be aware of dynamic loading! Sudden load
movement may briefly create excess load causing
product failure. Exceeding the maximum capacity for
this product is dangerous and can lead to serious injury
or property damage.
6. Never use this device as a work/repair station. Transfer
the load immediately to a suitable work station.
7. Always evaluate your task before using this product.
This Transmission Jack is designed to support a
transmission or a differential as individual components.
Use only as intended.
8. Assemblies such as differential with axle, or
transmission with bell housing, can be bulky and
difficult to balance. Lifting or supporting such
assemblies, even within weight limit, can create an
off-balance situation, causing the Transmission Jack
to tip over and MAY lead to serious personal injury or
property damage.
9. The load should be evenly distributed on the
Transmission Jack, and should not extend beyond the
area of the caster wheelbase. Always use the chains
provided to secure the load. If extra support is required,
safety straps (not included) can also be used to secure
the work piece.
10. Use only a hard, level and flat surface capable of
bearing the combined weight of the Transmission Jack,
the load being lifted, the operator and any tools being
used.
11. If loaded Transmission Jack must be moved, make
certain that the load is secured by appropriate means,
is stable, is in the lowest possible position, is moved
over a smooth, hard level surface, and that the lifting
platform is level.
12. If you are working and the load becomes off-balance
and/or the Transmission Jack begins to tip over,
WARNING
: DO NOT ATTEMPT TO CATCH OR LIFT
THE LOAD WHEN FALLING. SERIOUS PERSONAL
INJURY CAN RESULT! In this event, clear the area as
quickly and safely as possible in order to avoid injury from
the falling load, including getting hit with flying fragments.
13. Before each use, inspect the general condition of the
Transmission Jack. Check for oil leaks, Transmission
Jack operation, loose components, free rotation
and pivoting of saddle adjustment components. If a
problem occurs, have the problem corrected before
further use.
ASSEMBLY
1. Connect Bases (#43) to the pump frame by using a Flat
Washer (#48), Lock Washer (#49) and Bolt (#50).
2. Attach 2 pieces of Locking Castors (#47) and 2 Wheels
(#52) to the base by using Nut (#44), Flat Washer (#45)
and Lock Washer (#46).
3. Install the Saddle (#04) onto the Transmission Jack and
tighten the bolt on the saddle to secure the saddle.
WARNING
:
TO PREVENT SERIOUS INJURY: DO
NOT USE A DAMAGED OR MALFUNCTIONING JACK
.
1. Make sure the casters are locked before use.
2. The Transmission Jack is not designed to lift or lower a
vehicle.
3. If in doubt about the safety of your project, we advise
you to have the work done by a professional familiar
with applicable safety practices.
