3
Operating Instructions and Parts Manual
24660
11/18
2018 OEMTOOLS
™
20V MAX* LITHIUM-ION
3/8" DRIVE CORDLESS DRILL
4. To avoid injury from accidental starting, always remove the battery from the tool
before installing or removing a drill bit.
5. DO NOT install or use any drill bit that exceeds 7" (17.5 cm) in length or
extends more than 6" (15 cm) beyond the chuck jaws. They can bend or break
suddenly.
6. Before starting the operation, jog the drill switch to make sure the drill bit does
not wobble or vibrate.
7. DO NOT use fly cutters or multiple-part hole cutters, because they can come
apart or become unbalanced during use.
8. Make sure the spindle has come to a complete stop before touching the chuck
or attempting to change the drill bit.
9. Always make sure the chuck is tight and the drill bit firmly tightened in the
chuck before starting drill.
WARNING
:
Read Rules for Power Tool Safety.
IMPORTANT SAFETY INSTRUCTIONS
The warnings, precautions, and instructions discussed in this manual cannot cover all
possible conditions and situations that may occur. The operator must understand that
common sense and caution are factors which cannot be built into this product, but must
be supplied by the operator.
DISPOSAL
At the end of the useful life of the OEMTOOLS
™
Drill, dispose of the components
according to all state, federal, and local regulations.
BATTERY DISPOSAL
Exposure to high temperatures can cause the batteries to explode; DO NOT dispose
of in a fire. Some countries have regulations concerning battery disposal. Follow all
applicable regulations. Return used batteries to a collection location for recycling.
Call 800-822-8837 or visit www.call2recycle.org to find a collection location.
PURPOSE
The OEMTOOLS
™
20V MAX* Lithium-Ion 3/8" Drive Cordless Drill is used for drilling
holes, driving screws, loosening or tightening various materials together with fasteners
and other applications.
PRODUCT SPECIFICATIONS
Battery:
20V,1.5 Ah Li-ion
Keyless Chuck:
3/8"
2 Speed Gear Box:
0-350 RPM and 0-1,150 RPM (no-load)
Weight:
2.6 Lbs.
Charge Time:
3-5 Hrs.
Clutch:
16 + 1 Position
Auto Spindle Lock:
Yes
Max. Torque:
220 In/Lbs.
OPERATING INSTRUCTIONS:
Always wear safety goggles and gloves.
DRILLING
1. If drilling in a small workpiece, make sure it is securely held in a vise or
clamped to a secure platform such as a bench or table.
2. Install the correct drill bit in the chuck. Rotate the chuck body to loosen or tighten
the drill bit in the chuck. Never use the drill’s power to rotate the chuck body.
3. Select the rotation direction to clockwise, using the button located above the
trigger switch.
4. Select the correct transmission speed. Use the slower speed for drilling
large holes.
5. Set the torque adjusting collar to the drilling position (drill icon on tool).
6. Slide the fully charged battery pack onto the base of the handle.
7. Mark the drilling point with a center punch when drilling in metal to prevent the
drill bit from slipping off center as you begin drilling.
8. Place the drill bit at the location of the hole to be drilled and squeeze the trigger.
The harder you squeeze, the faster the drill turns.
DRIVING SCREWS
1. Install the correct screwdriver bit in the chuck. Use the largest bit size that will
properly fit the screw. Make sure the flat sides of the bit are gripped by the chuck.
2. Set the transmission speed to low speed.
3. Set the rotation direction to clockwise.
4. Set the torque collar to #10.
5. Place the screwdriver bit into the screw and hold the bit firmly into the screw to
prevent slippage and drive a test screw.
6. After driving a test screw, adjust the torque setting up or down so the screw is
driven to the desired depth without being over-driven.
7. Release the trigger immediately when the torque clutch begins to “rattle”.
8. Driven screws can be removed by reversing the direction of the rotation.
WARNING
:
Always charge the battery pack indoors in a well-ventilated area.
The charger must never be subjected to wet conditions.
ELECTRICAL WARNING
POWER SOURCE CONNECTION
POWER REQUIREMENTS
This product is designed to operate on a properly grounded 120 volt, 60Hz, single-phase
alternating current (AC) power source fused with a time delayed fuse or circuit breaker. It
is recommended that a qualified electrician verify the ACTUAL VOLTAGE at the receptacle
into which the product will be plugged and confirm that the receptacle is properly fused
and grounded.
DO NOT OPERATE THIS PRODUCT if the ACTUAL power source voltage is less than 105
volts AC or greater than 132 volts AC. Contact a qualified electrician if this problem
exists. Improper performance and/or damage to the product will result if operated on
inadequate or excessive power.
DO NOT abuse cord. Never use the cord to carry tools or pull the plug from an outlet. Keep
cord away from heat, sharp edges or moving parts. Replace damaged cords immediately.
Damaged cords increase the risk of electric shock.
CHARGING THE BATTERY PACK:
1. Place the discharged battery in a dry location near a 110-120V 60 Hz
electrical outlet.
2. Slide the battery charging cap onto the battery.
NOTE
:
Make sure the keys in the sides of the battery slide into the matching
grooves in the charging cap. Slide the charging cap as far as it will go onto the battery.
3. Insert the transformer plug into the charging cap.
4. Plug the transformer into the 110-120V 60 Hz wall receptacle.
BATTERY INDICATOR LIGHTS
1. The green indicator light will turn ON indicating the charger is “live.”
2. The red indicator light will turn ON when the charging cap is properly installed
onto the battery.
3. If the red indicator light does not turn on, check to make sure the charging cap
is slid fully onto the battery and the electrical outlet is working properly.
4. The green indicator light will turn ON when the battery is fully charged.
5. The battery should be left on the charger for 5 hours or until the green indicator
light turns ON to ensure it is fully charged.
6. It is normal for the battery charger to hum and be warm to the touch during
operation.
7. If the battery pack does not charge properly, check to make sure the electrical
outlet is “live.”
8. DO NOT charge batteries when the work area or the battery temperature is at
or below 32° (0°C) or above 113°F (45°C).
Green Light
Red Light
Battery on the
Charger
Charging Status
ON
OFF
NO
Charger connected to
power supply
OFF
ON
YES
Battery charging
ON
OFF
YES
Battery fully charged