OEM Tools 24498 Operating Instructions And Parts Manual Download Page 6

6

Operating Instructions and Parts Manual 

24498

HEAT GUN

10/18

2018 OEMTOOLS

3 POSITION TRIGGER SWITCH

 

The Heat Gun has a 3-position trigger switch that acts 
as both an ON/OFF switch and a temperature selector 
switch (Fig. 1). 

To turn the Heat Gun ON at the 

lower temperature 

(250° C or 482° F), squeeze the upper part of the 
switch (1). To turn the Heat Gun OFF from the lower 
temperature setting, squeeze the lower part of the 
switch (2) half way until it clicks into the OFF position 
and the Heat Gun turns OFF.
To turn the Heat Gun ON at the 

higher temperature 

(450°C or 842°F), squeeze the lower part of the 
switch (2). To turn the Heat Gun OFF from the higher 
temperature setting, squeeze the upper part of the 
switch (1) half way until it clicks into the OFF position 
and the Heat Gun turns OFF. 

NOTE:

 When the switch is set to the lower  

temperature setting, the motor speed will be slower 
and there will be a reduced flow of hot air through the 
nozzle. The temperature of the air will also be reduced 
to 482° F (250° C). When the switch is set to the higher 
temperature setting, the motor speed will be higher 
and there will be an increased flow of hot air through 
the nozzle. The temperature of the air will also be 
increased to 842°F (450°C).

NOTE:

 When the Heat Gun is first turned ON, smoke 

may appear due to the burning of manufacturing oils 
on the element. The smoke will disappear within five 
minutes of operation.

STRIPPING PAINT FROM DWELLING

 

The most common application for the Heat Gun is 
in stripping paint from fascia, soffit and siding of a 
dwelling (Fig. 2). Although the Heat Gun will work 
extremely well in this application, it is important to  
take specific precautions and prevent potentially 
serious mistakes.

WARNING

  

Use extreme caution if the opposite side of the work 
surface such as siding is not accessible. The hidden side 
could catch fire if it becomes too hot. Some buildings 
contain flammable material behind siding, floors, fascia, 
soffit boards and other such panels. Check these 
areas before applying heat. Do not use the Heat Gun if 
flammable materials are present or if you are unsure of 
the flammability of the hidden material. 
DO NOT use the Heat Gun on surfaces that can be 
damaged by heat, such as vinyl siding, vinyl coated 
siding or vinyl window frames. 
DO NOT use the Heat Gun on any glass surface such 
as windows. The rapid expansion may break the glass 
or damage the seal in thermo pane windows. 
The Heat Gun will soften putty in window frames. Be 
careful not to gouge the soft putty with the scraper. 
The putty will firm up as it cools. 
When removing paint from the fascia, do not overheat 
the edge of the shingles. Too much heat will melt the 
shingles. 

PAINT STRIPPING PROCESS 

 

WARNING

  

Never touch the Heat Gun nozzle during use or soon 
after use. It becomes very hot and will cause severe 
burns. Wear gloves to protect your hands from hot 
paint scrapings. 
When turned ON, the Heat Gun will heat the paint 
causing it to soften so it can be easily scraped off 
without damaging the surface. Some paints may 
soften when heated even though they show no signs 
of blistering. Some paints will blister when heated, 
while others may become rubbery. Some paints 
will require more heat than others to soften them 
sufficiently for easy removal.  

NOTE: 

Paint that has been absorbed into the wood 

will not be removed with the Heat Gun. 
When working with several layers of paint, completely 
heating the surface all the way to the wood will speed 
up the scraping process. This will allow all layers of 
paint to be scraped at one time. 
Use a soft wire brush to remove paint from very 
intricate surfaces. Mineral paints and finishes such 
as cement paint and porcelain do not soften when 
heated, so they cannot be removed using a Heat Gun.
For best paint removal results, move the gun slowly 
and steadily forward at an angle to the surface to be 

Fig. 2

Inside

Wall

Fascia

Soffit

Siding

Fig. 1

 1

 2

Summary of Contents for 24498









Reviews: