background image

Technical specifications 

 
Minimum operating voltage 

7 volts 

Maximum operating voltage 

18 volts 

 

(operating at or near maximum rating for an extended time can damage unit) 

Gauge Range 

 

 

0.0 - 17.0 volts 

Gauge 

Resolution 

  - 0.1 

Gauge 

accuracy 

  - 

±

0.1 V 

Typical current draw (@ 13.8V)  - 

0.13 A 

Warning indicator max current 

0.3 A 

 
 
 

ODYSSEY SERIES DIGITAL GAUGE LIMITED WARRANTY 

 

DAKOTA DIGITAL (the Company) warrants to the ORIGINAL PURCHASER of this product that should it, under 

normal use and condition, be proven defective in material or workmanship within 24 MONTHS FROM THE DATE OF 
PURCHASE, such defect(s) will be repaired or replaced (at the Company’s option) without charge for parts or labor 
directly related to repairs of the defect(s). 

To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of 

warranty coverage (e.g. dated bill of sale), name, address, phone number, and specification of defects, transportation 
prepaid, to the factory.  This Warranty is valid for the original purchaser only and may not be transferred. 

This warranty does not cover nor extend to damage to vehicle  electrical system.  This Warranty does not apply 

to any product or part thereof which in the opinion of the Company has been damaged through alteration, improper 
installation, mishandling, misuse, neglect, or accident. 

This Warranty is in lieu of all other express warranties or liabilities.  ANY IMPLIED WARRANTIES, INCLUDING 

ANY IMPLIED WARRANTY OF MERCHANTABLITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN 
WARRANTY.  ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED 
WARRANTY OF MERCHANTABLITY MUST BE BROUGHT WITHIN A PERIOD OF 24 MONTHS FROM DATE OF 
ORIGINAL PURCHASE.  IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR 
INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, 
WHATSOEVER.  No person or representative is authorized to assume for the Company any liability other that expressed 
herein in connection with the sale of this product. 

The Company does not warrant that this product cannot be compromised or circumvented.  THE EXTENT OF 

THE COMPANY’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED 
ABOVE AND, IN NO EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE PAID TO THE 
PURCHASER FOR THE PRODUCT. 

 

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation if 

incidental or consequential damage so the above limitations or exclusions may not apply to you.  This warranty gives you 
specific legal rights and you may also have other rights which vary from state to state. 

 
 
 
 

 
 
 

  

     4510 W. 61ST St. N.,  Sioux Falls, SD  57107 
   Phone: (605) 332-6513      FAX: (605) 339-4106  

 

         

www.dakotadigital.com

[email protected]

 
 

 ©Copyright 1997 Dakota Digital Inc. 

Summary of Contents for ODY-05-2







Reviews: