background image

Installation

6

 ACC-SVN121C-EN

3. Identify the wire harness with wire numbers 27B (red) 

and 29B (black).

4. Connect wires 27B and 29B to L1 and L3 respectively of 

the load side of the fuse block. Wire colors should 
match.

5. Note voltage labels on primary of the transformer. 

Screw transformer into control box as shown in 

Figure 4, p. 6

. Ensure reset switch is facing out.

6. Connect wire 29B to COM on the primary of the 

transformer. Connect wire 27B to the appropriate tap 
on the primary of the transformer, corresponding to 
unit supply voltage.

7.

Install pop-in wire tie and snap bushing as shown in 

Figure 4

.

8. Connect wires 35P, 37T, and 36D to the secondary of the 

transformer as shown in 

Figure 9, p. 11

. Attach ground 

wire 36D to control box using provided screw and lock 
washer.

9. Route wires 35P and 37T through snap bushing to LTB2 

along with existing wiring. Connect 35P to LTB2-R and 
37T to LTB2-B2 as shown in 

Figure 9, p. 11

.

10. Neatly collect wire slack in pop-in wire tie. Use other 

wire ties to secure wires as desired.

11. Apply transformer diagram, reset label, and safety 

agency label in locations shown in 

Figure 4

.

Figure 4.

Transformer installation - 2-speed unit

Safety Agency

Summary of Contents for BAYTFMR011













Reviews: