background image

 

 

 

2. SAFETY INSTRUCTIONS 

  

 

2.1. Before you begin 

 

Please read this Owner's Manual before you use 
the equipment for the first time. 

Operating the amplifier without its protective grille 
is dangerous and not recommended. 

 

In  case  of  emergency:  disconnect  the  plug 
from the mains supply. 

Never use an amplifier that is damaged or faulty. 
Make sure that it cannot be used until it has been 
repaired by a qualified service engineer.  
Make  sure  that  there  is  easy  access  to  the  IEC 
socket and power cord. 
 

Do not open the case 

There  are  dangerously  high  voltages  and  hot 
tubes  inside  this  equipment.  To  avoid  burns  or 
the  risk  of  electric  shock,  never  allow  anyone 
except  qualified  personnel  to  open  the  case  or 
remove the grille. 
 

Servicing and maintenance 

For  reasons  of  safety,  please  ensure  that 
servicing,  repairs  and  other  modifications  to 
OCTAVE  equipment  are  carried  out  only  by  a 
qualified  technician.  Fuses  should  be  also  be 
changed  only  by  a  qualified  technician.  Always 
replace  fuses  with  ones  of  the  same  type  and 
rating. If your amplifier requires servicing, please 
ship or take your equipment directly to OCTAVE 
or to one of our authorized service centers. 
 

Explanation of the warning symbols

 

 

 
 

The  lightning  flash  with 
arrowhead  symbol  within  an 
equilateral 

triangle 

is 

intended  to  alert  the  user  to 
the  presence  of  uninsulated 
'dangerous  voltages'  within 
the  product's  enclosure  that 
may 

be 

sufficient 

to 

constitute  a  risk  of  electric 
shock to persons. 
 
The exclamation point  within 
an  equilateral  tri-angle  is 
intended  to  alert  the  user  to 
important 

operating 

and 

maintenance instructions. 
 
 

Before connecting up 

Make  sure  that  the  voltage  of  your  amplifier 
matches with your electricity supply voltage.  
 

Grounding 

This  amplifier  is  a  protection  class  1  device 
(with an earth conductor). To exclude the risk of 
electric  shock  in  the  event  of  a  fault,  the  unit 
must  be  grounded.  Use  a  three-core  mains 
cable with a three-pin plug (supplied). 
 

Safety warning: Hot tubes

Warning:  Remove  the  protective  grille  at  your 
own  risk.  OCTAVE  cannot  accept  any 
responsibility for injuries caused by the removal 
of this grille.  
 

Warranty 

OCTAVE  can  only  guarantee  the  safety, 
reliability  and  performance  of  this  unit  if 
modifications  and  repairs  are  carried  out  by 
specialized  personnel  and  if  the  amplifier  is 
operated  in  accordance  with  the  instructions 
contained in this manual. 

 

 

 

 

 

 
 
 
 
 
 

 

Summary of Contents for JUBILEE MONO SE
































Reviews: