B-6 (2)
103743-001
Box Contents
Install Seat
A
Hardware Pack
Latin America/Asian Pacific
001-763-757-2662
Europe/Middle East/Africa
31-10-2662412
Questions?
octanefitness.com
113201-001 REV E Page 1/2
USA & Canada
888-OCTANE4
©2020 Octane Fitness. All rights reserved.
Base
(xR6000 shown)
Tools Required:
#2 Phillips screwdriver
17mm wrench
Moving Handlebars
(Right and Left)
112508-001
112509-001
Information Packet
113201-001 Assembly
107786-001 Safety Instructions
B-1 (1)
B-2 (1)
B-9 (4)
B-4 (2)
B-5 (4)
105717-001
8022048
B
Install
Mast
C
Install Console
Separate console back from console front; set console back aside (not shown).
Connect the C-SAFE cable from the mast cover to the console (cable not
shown).
Note:
If you are installing a 900 MHz accessory, remove and
discard the C-SAFE cable.
Connect heart rate cable attached to heart rate board on console back
to heart rate cable from mast (black, 6-pin connector).
Make additional cable connections from mast to back of console:
Standard Console:
power,
handlebars,
base,
LAN,
ground
Smart Console:
power,
handlebars,
base,
LAN
(leave ground unconnected)
Routing loose cables to user front side of mast brackets, attach console front to
top of mast with C-1 (quantity 4); tighten using Phillips #2 screwdriver. Remove
screw securing mast cover to mast; retain screw. (If C-SAFE cable is in use,
let mast cover hang from cable.)
For Smart console only:
Install power switch; connect cable and power.
a. Remove rubber plug from mast cover (not shown).
b. Route two-connector end of switch cable (pre-connected to console) through the
opening where plug was removed. Attach connectors to tabs on switch
(either connector can go on either tab).
c. Press switch fully into opening of mast cover; let mast cover hang
from cables.
d. Connect power cord and power supply. Plug into base of unit
and wall socket to verify power to console. Unplug from wall socket before
continuing to step D.
Standard Console Box Contents
5mm hex wrench (provided)
Tools Required:
#2 Phillips Screwdriver
Information Packet (attached to console)
110601-001 Notice to Installers
111289-001 xR6000 Console Guide & Setup
Instructions–Standard Console
104198-001 Warranty
101315-001 Registration Card
Standard Console
(Front and Back)
8020168
Tools Required:
#2 Phillips Screwdriver
110601-001 Notice to Installers
111768-001 Console Guide & Set-up Instructions–
Smart Console
104198-001 Warranty
101315-001 Registration Card
Information Packet (attached to console)
Smart Console
(Front and Back)
8019479
Standard
Console
Smart
Console
Console to Base
(white, 14-pin)
Handlebar Control
(white, 7-pin)
Console Ground
(metal; green wire from mast)
Reserved
(unused)
Audio for
Accessories
(unused)
Power
(white, 4-pin)
Power for
Accessories
(unused)
Reserved for
Software Field Update
(black)
LAN
(RS-232)
C-SAFE
(Connect from mast
cover in Step
)
Standard Console
Power Switch
111032-001
Power Supply
112584-001
#2 Phillips
C-1 (10)
100780-001
Hardware Pack
110622-001
#2 Phillips
C-1 (10)
100780-001
Hardware Pack
110622-001
F-2
(may be boxed separately)
Power Cord
107658-001
(may be boxed separately)
Smart Console
Handlebar Control
(white, 7-pin)
Console to Base
(white, 14-pin)
Power
(white, 4-pin)
LAN
(RS-232)
(on Android board
underneath)
Power for
Accessories
(unused)
(unused)
(unused)
(unused)
(unused)
(unused)
(unused)
C-SAFE
(Connect from mast
cover in Step
)
Arm Pivot Cover–Large
(Right and Left)
113185-001
Hardware Pack
112844-001
6mm
5mm
B-6 (2)
112734-001
B-11 (4)
112223-001
B-13 (2)
B-12 (2)
B-10 (2)
101277-001
Console Mast
112738-001
Foot Rest/Accessory Tray
112824-001
Foot Pedals
(Right and Left)
116661-001
111660-001
Seat Back
Enter
PAUSE
CLEAR
Time
Calories
Distance
Speed
HR%
HR
Level
Challenging intervals isolating legs for power and toning
Higher resistance intervals isolating arms, shoulders and chest
A built-in personal trainer to motivate you with intense intervals
HIIT BOOSTERS
Program
Workout
Narrow Grip Wide Grip
Reverse
Legs Only
Res
Push Arms Pull Arms
Fast
PRESS TO ACTIVATE
Quick Start
Level
OCTANE
FAVORITES
MMA
30:30
(Install back cover
and mast cover, C-SAFE
cable not shown)
6mm hex wrench (provided)
6-c
F-2
(Install back cover
and mast cover, C-SAFE
cable and power switch
cable not shown)
F-2
F-2
6-d
Flat head screwdriver
Assembly Instructions
(not shown)
112832-001
113183-001
Arm Pivot Cover–Small
(Right and Left)
113182-001
113184-001
Smart Console Box Contents
Use 6mm hex wrench to remove bolt and
washer from right side of seat back axle;
slide axle out user left side.
Position seat back; insert axle from left side through seat back
bracket, aligning flat sides of axle and hole. Align washer and
bolt with axle; tighten with 6mm hex wrench to 19 ft-lb.
Insert spacer B-2 (quantity 1) through hole in damper. Tilt seat
and align damper/spacer in seat bracket. Insert screw B-1
(quantity 1) through bracket and damper/spacer;
tighten with 5mm hex wrench to 7 ft-lb.
Test seat height and tilt adjustments to verify function of locking
mechanisms (not shown). (On xR6000s, also test swivel mechanism.)
Remove all loose parts from packaging; use handle to
lift rear of base and gently roll unit off
shipping pallet.
112736-001
113194-001
109989-001
104757-001
103743-001
8008949
6mm Hex (1)
103083-001
5mm Hex (1)
Use #2 Phillips screwdriver to remove two screws
securing front and rear top shrouds and mast boot. Set
screws, shrouds, and mast boot aside (not shown).
Remove twist tie securing cable bundle; tip mast
upside down and route cables through hole in
bottom of mast to top of mast.
Slide mast over screws on base; insert screw B-3
(quantity 2) into holes in front of mast plate, tighten
with 6mm hex wrench.
Insert screw B-3 (quantity 2) into holes in top of
mast plate. Use 6mm hex wrench to tighten
all 6 screws
to 30 ft-lb.
Align bottom of front top shroud with base, then tip up
into position. Position rear top shroud and mast boot,
then secure both top shroud pieces using #2 Phillips
screwdriver and two screws removed in step 1.
B-3 (4)
101295-001
6mm
100780-001
#2 Phillips
B-8(4)
13mm
13mm
6mm
Rubber mallet
(optional)
Side Step (2)
113208-001
(xR6000s only)
cables
through
here
13mm wrench
Read and understand the “Product Safety Information” manual
before assembly.
B-7 (2)
103393-001
