manualshive.com logo in svg

Ocean Technology Systems MK-7 BUDDY-LINE, User Manual, Page: 5 / 20

Share
Download
Ocean Technology Systems MK-7 BUDDY-LINE User Manual Download Page 5

SECTION 2

2.1  MK-7 BUDDY-LINE

®

 SPECIFICATIONS:

Input Voltage:

12 VDC.

Input Current:

600 mA peak.

Idle Current:

30 mA.

Frequency Response:

600 Hz to 10 kHz.

Microphone Type:

Dynamic

Power Output:

2 watts RMS.

Battery Type:

Eight AA Alkaline batteries (Alkaline only).

Battery Life:

12 hours using eight AA Alkaline batteries.

Battery Options:

RB-11 NiMH rechargeable battery pack. RC-16
battery charger (charging time: 14 hours).

Housing:

Injection-molded, high-impact plastic.

Size:

Height: 6.750” from bottom to top of connector
Width: 4.250” from latch to latch
Depth: 2.750” from front knob to rear buckle

Weight:

1.0 pounds, without batteries.

ComRope Length:

Up to 1200 feet.

ComRope:

Nylon, static Kernmantle rope specially de-
signed with two 18 awg and two 24 awg wires
manufactured in the center.  Breaking point ap-
proximately 5800 lbs. for the rope and 500 lbs.
for the communication wires.

2

Summary of Contents for MK-7 BUDDY-LINE





















Reviews:

No comments