background image

 

17 

 
 
 
 

3.2.3  

Photocell 

 
If included in the system, the ambient light sensor (photocell) should be mounted upright, away from 
artificial  light  (such  as  floodlights),  and  in  a  location  that  will  enable  its  sensor  window  to  have  an 
unobstructed view of the polar sky (eg., pointed north in the northern hemisphere).  
Make the connection of the external photocell and the power supply to 

TB1 in the power supply as 

per figure 3-1 page 18

 

3.2.4 

GPS antenna (option) 

 
If  GPS  included  in  the  system,  the  magnetic  antenna  of  the  GPS  should  be  mounted  on  a  ferrous 
metallic  part  without  an  unobstructed  view  to  the  sky.  The  5  meters  cable  provided  with  the  antenna 
shall be connected in the jack plug located in the front side of the GPS module. 

 

3.3 

120VAC to 230VAC Power cable 

 
Make the connection of the AC power supply to 

TB1 in the power supply as per figure 3-1 page 17 

and figure 3-2 page 18 

 

 

3.4       Final Check 

 
Before applying power to the equipment, check all wire connection and ensure that any user-installed 
wiring does not interfere.   

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for OBSTAFLASH Led

























Reviews: