OBH Nordica Perfect Mix+ LH871DS0, Instructions For Use Manual

Page: 31 / 35

61 60
ASSEMBLING AND FITTING THE JUG
Moisten the seal (F3, O3) (even if already fitted on the blade unit
(F1, O1) ). Be careful to correctly fit the seal (F3, O3) back onto the
blade unit (F1, O1) the correct way up (Fig 17) .
• Check the seal is in place on the blade unit.
• Place blade unit on the locking ring (Fig 1, Fig 7) .
• Turn the jug upside down and place blade unit with locking ring
on the base.
• Make sure the locking ring is locked correctly : the two arrows must
be aligned (Fig 3, Fig. 9) .
• Add the ingredients to the assembled jug without exceeding the
maximum level indicated:
* 1.5 L for thick mixtures
* 1.25 L for liquid preparations
Warning: Do not pour boiling liquids (over 80°C/176°F) into the jug.
Do not insert any metallic object into the blender. Do not mix pieces
of frozen ingredients larger than 25x25x25mm.
• Fit the lid (F5, O5) on the jug (Fig. 6, Fig. 12) . To avoid any splashes
during blending make sure that the curved tabs on the lid are aligned
with the spout and handle (Fig. 5, Fig. 11) . Fit the measuring cap
(F6, O6) in the hole on the lid (Fig. 8) . Then position the bowl on the
motor unit and turn it 1/4 turn clockwise (Fig 4 / Fig 10).
USING YOUR BLENDER
• Once the blender jug is locked correctly on the motor unit, plug in the
appliance. The lights on the appliance flash twice and you hear a beep.
Turn it on using the desired function.
• Speed selection: Turn the control knob (E) to choose the desired speed;
the speed increases gradually between min and max . The intensity of
the lights on the appliance increase gradually as the speed increases.
You can change the speed as required during preparation.
• “Pulse” function: Turn the control knob (E) to the “Pulse” position.
Using a succession of pulses gives finer control for precise
preparations. In this position, the appliance starts directly on
maximum speed. It stops as soon as you release the knob.
The light remains on when the pulse function is in use.
• Function “ Smoothie”
This function is used to prepare smoothies, milkshakes and fruit
cocktails. The speed is pre-programmed for best results. To use
this function, press the “Smoothie” button (B) . The light remains
on during this cycle and switches off when the cycle is finished.
The program stops automatically. You can stop it before the end by
positioning the control button (E) on 0.
• Function “ Ice crush”
You can use this function to crush ice finely with pre-programmed
operating cycles and speed. To use this function, press the “Ice
crush” button (C) . The light remains on during this cycle and
switches off when the cycle is finished. You hear 4 beeps. The
program stops automatically but you can stop it before the end by
positioning the control button (E) on 0.
• Function “Auto clean”:
This function is used to automatically clean your appliance. Press the
“Auto clean” button (D) . Do not exceed 1 litre of hot water (maximum
temperature of 80°C / 176°F). At the end of the program, the
appliance stops automatically.
• WARNING : If the load becomes too high, your appliance will stop
automatically for safety reasons (if the motor runs for more than
3 minutes or if you have used too much ingredients) . To restart your
appliance, turn the control knob to . The overall cooling time may
vary and can be up to 30 minutes. Before restarting your appliance,
adapt the quantity of ingredients or blending time to avoid any
overload. You can then select the desired speed or function to
complete your preparation.
• WARNING : Do not use the program functions smoothie, ice crush
and auto clean with the spice grinder (K).
These programs can only be used with the blender jug (F) . Do not
perform ice crush with the spice grinder (K) .