2 of 7
requirements. Plug power supply cord into wall outlet. The rear most 1-3/8 diameter knockout in frame bottom is for
an externally located electrical supply. Make sure knockout hole edge is smooth and free of any burrs. Use of Heyco
bushing #2184 in knocked out hole is recommended to prevent damage to service cord and to close up excess opening
around cord. Route cord so it does not interfere with ADA* space requirements.
14.
To fill cold water tank on water cooler, open water supply line shut-off and push any one of front push pads to allow
water to flow to bubbler. On TM and TT models, actuate solenoid by holding one hand approximately 1” from
infrared sensor (under front edge of shelf). Run water until stream is free of bubbles. After approximately 20 seconds
run time, solenoid valve will automatically shut off. To reactivate, move hand away for an instant and then again
place it in front of sensor.
15.
To Adjust Bubbler stream:
All models are equipped with a cartridge regulator. The standard push pad and electric eye models have a slot at
back of underside of shelf. Insert a screwdriver in this slot to adjust regulator. Turn adjustment clockwise to
increase stream height. To access PGV8ACSL and PGVF8ACSL adjustment, remove the Bezel and Button from
front of cooler.
14.
On electric eye equipped models (TM and TT models), place and then hold hand approximately 1” from sensor (under
front edge of shelf) to actuate solenoid valve. After approximately 20 seconds run time, solenoid valve will
automatically shut off. To reactivate, move hand away for an instant and then again place it in front of sensor. Every
time the power reboots, the bottle sensor automatically recalibrates itself. IT IS IMPORTANT TO HAVE NO
OBJECT PRESENT NEAR THE SENSOR EVERYTIME THE UNIT REBOOTS SO THAT SENSOR
CALIBRATION IS DONE CORRECTLY.
C.
MAINTENANCE
The only maintenance operation required is the removal of dirt and lint from the condenser of the water cooler. Inspection
should be made at 3-month intervals. Disconnect the power supply cord, then clean the condenser with a small stiff non-
wire brush when required. Observance of this procedure will ensure adequate air circulation through the condenser, so
operation is efficient and economical.
D.
OVERLOAD PROTECTION (water cooler)
The compressor motor, where used, is equipped with an automatic reset protector which will disconnect the motor from
the line in case of an overload.
E.
LUBRICATION (water cooler)
This unit is equipped with a hermetically sealed compressor and requires no additional lubrication. The fan motor on this
unit seldom needs oiling, but if required, a few drops of SAE 10 oil should be used.
F.
TO DISCONTINUE USE OF WATER COOLER AND WATER FOUNTAIN
1.
Close water shut off valve.
2.
Provide container to catch water to be drained.
3.
On push button model, disconnect power supply cord then disconnect water supply line at shut off valve. Route water
supply line to container and actuate push button. If this drains too slowly for you, prepare 3/8” ID tube or 3/8” OD
tube with quick-connect fitting and remove screw plug in tank drain. Slide tube over drain and route to container.
Replace screw plug when draining is complete. Do not over-tighten. O-ring only needs to be snug to seal.
4.
On TM and TT models, disconnect water supply line at shut off valve. Place water supply line in container and
actuate solenoid as explained in Step B12. If this drains too slowly for you, disconnect power supply cord and prepare
3/8” ID tube or 3/8” OD tube with quick-connect fitting. Remove screw plug in tank drain. Slide tube over drain and
route to container. Replace screw plug when draining is complete. Do not over-tighten. O-ring only needs to be snug
to seal.
5.
ALWAYS DRAIN ALL WATER WHEN FREEZING TEMPERATURES ARE ANTICIPATED AND BEFORE
SHIPPING THE WATER COOLER.
*American With Disabilities Act
WARNING
The warranty and the Underwriters' Laboratory listing for this machine are automatically voided if this machine is altered, modified, or
combined with any other machine or device. Alteration or modification of this machine may cause serious flooding and/or hazardous
electrical shock or fire.
EXCEPT AS SET FORTH HEREIN, THE MANUFACTURER MAKES NO OTHER WARRANTY, GUARANTEE OR
AGREEMENT
EXPRESSED,
IMPLIED
OR
STATUTORY,
INCLUDING
ANY
IMPLIED
WARRANTY
OR
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
