background image

TROUBLESHOOTING (TO BE PERFORMED BY STORE PERSONNEL UNLESS STATED OTHERWISE) 

18 

CONDITION 

TROUBLESHOOTING 

Water Is On The Floor 

Floor drain units: Check that drain (at underside of case) is properly routed 

to floor drain. 

 

Call service provider. 

Fans Emit Excessive Noise 

Call service provider. 

No Case Lights Are       

Working 

Check that light switch is in the 

on

 position.

 

 

Check that ALL of the light cords and plugs are properly connected. See 

MAINTENANCE FUNDAMENTALS - SHELF & BRACKET ASSEMBLY 

REMOVAL / LIGHT FIXTURES 

section in this manual for specifics. 

 

Authorized Service Contractors Only:

 

Check circuit breaker box for 

tripped circuit. 

 

 

If case lights still do not come on, call service provider.

 

One (or Several) Case 

Lights are Not Working 

Check that ALL of the light cords and plugs are properly connected. This 

includes the following items: 

 

Oval form of plug must connect to oval form of LED light. 

 

The power end of cord is to connect at the “red dot” marker at the end 

of the LED lamp. 

 

See 

MAINTENANCE FUNDAMENTALS - SHELF & BRACKET       

ASSEMBLY REMOVAL / LIGHT FIXTURES 

section in this manual 

for more specifics including illustrations. 

 

If case light still do not come on, call service provider.

 

Case is Not Holding Proper 

Temperature 

If a large amount of warm product was added to the case, it will take time 

for the temperature to adjust.  Product must be pre-chilled before placing 

in case. 

 

Check that the case is not in the sun or near a heat or air-conditioning 

vent.  See 

OVERVIEW / TYPE / COMPLIANCE / WARNINGS /          

PRECAUTIONS / WIRING DIAGRAM 

section in this manual for         

specifics. 

 

If case is located near front doors, temperature fluctuation can hinder 

unit’s ability to maintain temperature.  See 

OVERVIEW / TYPE /        

COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING DIAGRAM   

section in this manual for specifics. 

 

Check air return grilles (area at front of decking) for obstructions.           

DO NOT set product on air grilles as this will prevent proper airflow! 

 

If case still is not holding proper temperature, call service provider.

 

Summary of Contents for FSC463R






























Reviews: