8
31.
Use the (+) or (-) button to set the total number of months you wish to monitor up to. The maximum number you
can enter is 12 months and it does not roll over to 0 after this value. Hold down the (+) or (-) button to roll through
the numbers.
32.
To turn the UV bulb monitor on or off, hold the “CLOCK SET” button and press the “POWER” button while in
UV bulb life monitor set up mode. The word “ON” will appear above the digits when the monitor is turned on, and
will disappear when the monitor is off. As long as the monitor is “ON”, the number of months displayed will count
down to “00.” When it is not “ON,” it will remain at the current value displayed.
33.
Press the “POWER” button again to set the month count in memory.
34.
To turn the cooler back on, press the “POWER” button one more time. This process is also how you reset the
month counter once the previous month count has reached “00.”
HOT BOOSTER MODE
Use the HOT BOOSTER mode when you want to get hot water that is heated to the optimal temperature needed for tea, soup,
coffee and hot chocolate.
Push the “HOT BOOSTER” button to turn on the hot tank and heat the water to 200°F. During this time, the words “HOT
BOOSTER” appear. It will take anywhere from 1-4 minutes for the HOT BOOSTER to heat the water up to the optimal
200°F. When the HOT BOOSTER water is ready, there is an audible 5 second beep and the words “HOT BOOSTER
WATER READY” will light up for 10 seconds and then go out.
WARNING: Water is extremely hot and can cause
burns or death from scalding. Children, the disabled and elderly are at highest risk of being scalded. Use hot water
faucet with extreme caution.
LOCKING THE DISPLAY CONTROLS
Use the locking function if you want to keep people altering your settings. This may be especially important if children will
have access to the cooler. To engage the lock, press and hold the (+) and (-) buttons at the same time for 3 seconds. After 3
seconds, you will hear a single beep and the word “LOCKED” will be displayed above the cup icon. Once the lock has been
engaged, no cooler settings can be changed. The hot booster will continue to work. To remove the lock function, press and
hold the (+) and (-) buttons again for 3 seconds. After 3 seconds, you will hear a double beep and the word “LOCKED” will
disappear. Now the locking function has been turned off and you can use the other buttons to adjust cooler settings as
needed.
CONTROL PANEL QUICK REFERENCE
•
The “HOT BOOSTER” turns on the hot tank and heats the water to 200°F which is the optimal temperature needed for
tea, soup, coffee and hot chocolate. During this time when the water is being heated (usually 1-4 minutes), the words
“HOT BOOSTER” appear. When the HOT BOOSTER water is ready, there is an audible 5 second beep and the words
“HOT BOOSTER WATER READY” will light up for 10 seconds and then go out.
•
The cup icon flashes when the hot tank element is ON and heating water.
•
The snowflake icon flashes when the compressor is ON and cooling water.
•
Use the (+) or (-) button to set the clock, the ENERGY SAVER mode timing, the temperature of hot and cold water, the
filter life monitor and UV bulb life monitor.
•
Press “ENERGY SAVER” to turn “ON” the ENERGY SAVER mode. The words ‘ENERGY SAVER ON” will light
up. Press again and the mode is turned ‘OFF.” The words “ENERGY SAVER ON” will disappear.
•
Press the (+) and ‘POWER” buttons at the same time to change or reset the filter life monitor gallon count.
•
Press the “HOT BOOSTER” and “POWER” buttons at the same time to change or reset the UV bulb life monitor.
•
Press the (+) and (-) at the same time and the other buttons are disabled until this combination is pressed again. The
word “LOCKED” is displayed above the cup icon.
CLEANING THE OUTER HOUSING
1.
Press “POWER” to turn off the LCD display, if applicable. Unplug the water cooler.
KEEPING YOUR COOLER CLEAN
