Oakton pH 10 Series Operating Instructions Manual Download Page 2

Page: 2 / 13

Table of Contents

1. Introduction ..............................................................................Page 4

Getting started • Maintenance, troubleshooting

2. Display and keypad functions.................................................Page 5

3. Preparation ...............................................................................Page 6

• Inserting the batteries • Connecting the electrode and
temperature probe • Attaching the electrode holder to the
meter • Inserting the electrode into the electrode holder
• Connecting the AC adapter

4. pH calibration ...........................................................................Page 8

• 1-point pH calibration • 2- or 3-point pH calibration

5. pH measurement....................................................................Page 10

• Measurement with Automatic Temperature Compensation
• Measurement with Manual Temperature Compensation

6. mV measurement ...................................................................Page 12

7. HOLD feature .........................................................................Page 13

8. Temperature calibration........................................................Page 14

• 1-point temperature calibration • Two point temperature
calibration

9. Electrode care and maintenance .........................................Page 17

• Storage • After measuring • To reuse the electrode
Electrode cleaning • Reactivating the electrode

10. Error messages .....................................................................Page 19

11. Troubleshooting ....................................................................Page 20

12. Specifications........................................................................Page 20

13. Accessories ...........................................................................Page 21

14. Warranty ................................................................................Page 22

15. Return of items......................................................................Page 22

Page 3

Page 2

Summary of Contents for pH 10 Series














Search results

Summary of Contents for pH 10 Series

Reviews:

Related manuals for pH 10 Series

Brands by name

Popular brands

Oakton pH 10 Series, Operating Instructions Manual

Search results

Summary of Contents for pH 10 Series

Reviews:

Related manuals for pH 10 Series

Brands by name

Popular brands