background image

29

ADJUSTING CHART

High Speed Needle Valve - 2 turns opened from fully closed position.
Idle Mixture Control Screw - 2 turns opened from fully closed position.

Start the engine

Warm up the engine

Observe the mixture condition while "floating" the model

Turn the Idle Mixture
Control  Screw  counter-
clockwise 10 degrees

Idling OK

Turn the Idle Mixture
Control Screw
clockwise 10 degrees

Lean mixture

Rich mixture

Observe the hovering mixture condition

Open the High Speed
Needle Valve
(Turn counter-clockwise)

Hovering OK

Lean mixture

Rich mixture

Close the High Speed
Needle Valve
(Turn clockwise)

Land the model

Idle for approx: 10 seconds, then reopen throttle to 
observe transition ("Float" the model) 

Idling OK

Lean mixture

Rich mixture

High Speed Flight

Lean mixture

Rich mixture

High Speed Flight OK

Fine tuning of hovering mixture

Hovering OK

Adjustment completed

Open the High Speed
Needle Valve
(Turn counter-clockwise)

Close the High Speed
Needle Valve
(Turn clockwise)

Fine tuning of idling mixture

Lean mixture

Rich mixture

Idling OK

Turn the Idle Mixture
Control Screw
clockwise 10 degrees

Turn the Idle Mixture
Control Screw
clockwise 10 degrees

Turn the Idle Mixture
Control  Screw  counter-
clockwise 10 degrees

Turn the Idle Mixture
Control  Screw  counter-
clockwise 10 degrees

Summary of Contents for MAX-91SX-HRING C Spec PS VIPER






















Reviews: