background image

If the engine produces a higher pitch sound immediately after taking off or if the engine appears to 

lose power and exhaust cannot be seen at all (although varying somewhat depending on the fuel), 

turn the injection trim adjustment dial (spare channel dial) in the (+) rich direction by about 45˚ with 

the throttle stick in the full high position and reconfirm engine operation by continuing to fly for 3-4 

minutes.  (When this is difficult to evaluate, land the airplane and recheck engine speed with the 

throttle stick in the center and full high positions.)  When there is still no change even when the 

above adjustment has been made, land the airplane and try readjusting from the first step of the 

adjustment procedure.  This completes the adjustment procedure.

GLOWPLUGS

The role of the glowplug

Glowplug life
Particularly in the case of very high performance engines, glowplugs must be regarded as 
expendable items. 

Fit a plug suitable for the engine.

Use fuel containing a moderate percentage of nitromethane unless more is essential for racing 
events.

Do not run the engine too lean and do not leave the battery connected while adjusting the 
needle. 

However, plug life can be extended and engine performance maintained by careful use, i.e.:

With a glowplug engine, ignition is initiated by the application of a 1.5-volt power source. When the 
battery is disconnected, the heat retained within the combustion chamber remains sufficient to 
keep the plug filament glowing, thereby continuing to keep the engine running. Ignition timing is 
'automatic' : under reduced load, allowing higher rpm, the plug becomes hotter and, appropriately, 
fires the fuel/air charge earlier; conversely, at reduced rpm, the plug become cooler and ignition is 
retarded.

Once adjustment has been completed, when the airplane is flown again, simply recall the TMD 

menu by pressing the function key.  The display changes from the Fine menu to the ATL menu.  

(Fine adjustment data continues to be stored in memory.) Next, switch to the ATL adjustment 

menu.  The function of the injection trim adjustment dial changes to that during Fine with full high 

corresponding to 100% (see the previous section on TmD ATL) based on full slow corresponding 

to the origin. It is recommended to use this menu during routine flights. Repeat the fine adjustment 

procedure described above whenever the propeller or fuel and so forth has been changed.

Since the compatibility of glowplug and fuel may have a marked effect on performance and 
reliability, it may be worthwhile to choose the R/C type plug found most suitable after tests.
Recommended O.S. plugs are TYPE F. Carefully fit plug finger-tight, before final tightening with the 
correct size plug wrench.

Apart from when actually burned out, a plug may need to be replaced because it no longer 
delivers its best performance, such as when:

When to replace the glowplug

Filament surface has roughened and turned white. 

Filament coil has become distorted.

Foreign matter has adhered to filament or plug body has corroded.

Engine tends to cut out when idling.

Starting qualities deteriorate.

16

Summary of Contents for MAX 140RX FI

























Reviews: