manualshive.com logo in svg

O.S. engine MAX-12LD, Owner'S Instruction Manual, Page: 8 / 29

Share
Download
O.S. engine MAX-12LD Owner'S Instruction Manual Download Page 8

INSTALLATION OF E-1000 SILENCER

 

(12/15LD

(

T

)

.LD-X

(

T

)

)

Fit the nipple (supplied) to 
the silencer, applying heat-
resistant epoxy sealant at 
the roor of the fitting (See 
sketch).

Before installing the engine 
in the chassis, secure the silencer to the en-
gine with M3X27mm screws.

Seal here applying 
heat-resistent 
epoxy sealant.

MODIFICATION OF O.S. E-1000 SILENCER FOR 
PRESSURIZED FUEL SUPPLY

•

•

THROTTLE  LINKAGE

The throttle-arm ball-link is adjustable. Loosen 
3mm set-screw and adjust the link so that link-
age rod and upper plate become parallel, and 
then retighten it securely. 
If the linkage rod and upper plate are not paral-
lel, throttle valve will not move smooth-ly and 
may dam-age the carburettor.

Adjust the ball link position so that 
linkage rod and upper plate become 
parallel by loosening 3mm set-screw. 

Upper plate

Throttle servo

3mm set-screw

Chassis

AIR CLEANER

The air cleaner of this engine is integrated with 
the engine shield. It contains a specially im-
pregnated filter element which prevents highly 
damaging dust and dirt from being drawn into 
the engine through the carburettor. 
An O-ring is fitted between the engine shield 
and carburettor to exclude air leaks.

8

Summary of Contents for MAX-12LD






























Reviews:

No comments