O.S. engine GT120THU Maintenance Manual Download Page 7 | Manualshive

Page: 7 / 21

O.S. engine GT120THU Maintenance Manual Download Page 7

6 / 20

④ Check the air cleaner

⑤ Check the plug cap and high-tension cord

⑥ Check the spark plug

⑦ Check the throttle linkage and the chock linkage

⑧ Check the throttle servo and the choke servo

⑨ Check all the screws.

⑩ Check all the wirings

(2)

Inspection after 50-hour operation

Do the following inspection in addition to the above inspection.

① Generator belt tension adjustment

② Regulate rectifier inspection

③ Generator inspection

④ Ignitor inspection

(3) Inspection after 100-hour operation

100 hours inspection means doing the check and maintenance as follows in addition to all the 25 and 50-hour

inspection.

① Disassemble and inspect each part of engine

i)

inspection and maintenance of the cylinder block

ii)

inspection and maintenance of the pistons

iii)

inspection and maintenance of the piston rings

iv)

inspection and maintenance of the piston pins

v)

inspection and maintenance of the crankshaft and the connecting rods

vi)

inspection and maintenance of the ball bearings

vii)

inspection and maintenance of the carburetors

viii)

inspection and maintenance of the generator

ix)

inspection and maintenance of the starter motor

x)

inspection and maintenance of the starter gears

xi)

inspection and maintenance of the one-way clutch

② Air cleaner maintenance

③ Fuel tube filer replacement

④ Fuel tube replacement

⑤ Generator belt replacement

5.

INSPECTION AFTER EVERY 25 HOURS OF OPERATING TIME

(1) Visual inspection of the engine

Check the engine if there are dents, damage, losses on the cooling fins. Check if foreign objects stuck between

the cooling fins to be removed. Check if there are oil leakages or oil stains, or fretting wears on the surface of it.

«
...
5
6
7
8
9
...
»

Summary of Contents for GT120THU






















Reviews:

No comments