background image

It  is  of  vital  importance,  before  attempting  to 
operate  your  engine,    to  read  the  general 
'SAFETY  INSTRUCTIONS  AND  WARNINGS' 
section  on  pages  2-4  of  this  booklet  and  to 
strictly adhere to the advice contained therein.

Also, please study the entire contents of this 
instruction  manual,  so  as  to  familiarize 
yourself with the controls and other features of 
the engine.
Keep these instructions in a safe place so that 
you  may  readily  refer  to  them  whenever 
necessary.
It is suggested that any instructions supplied 
with the aircraft, radio control equipment, etc., 
are accessible for checking at the same time.

1

 

14-15

SAFETY INSTRUCTIONS AND 
WARNINGS ABOUT YOUR O.S. ENGINE

INTRODUCTION, INSTALLING THE GLOWPLUG
BASIC ENGINE PARTS

RELOCATION OF CARBURETTOR CONTROLS
CHOKE VALVE

FUEL TANK, INSTALLATION

EXHAUST HEADER PIPE AND SILENCER,
THROTTLE LINKAGE, 
NEEDLE-VALVE EXTENSION

PROPELLERS,
PROPELLER AND SPINNER ATTACHMENT

FUEL

GLOWPLUGS

CARBURETOR

CONTENTS

RUNNING-IN

IDLE MIXTURE ADJUSTMENT

VALVE  ADJUSTING

CARE AND MAINTENANCE

O.S. GENUINE PARTS & ACCESSORIES

ENGINE EXPLODED VIEWS &
ENGINE PARTS LISTS

CARBURETTOR EXPLODED VIEWS &
PARTS LIST

ENGINE THREE VIEW DRAWINGS

NOTE

STARTING

12-13

2-4

5

6

7

8

9-10

10

11

12

24

15

16-17

18

19

20-21

22

23

Summary of Contents for FS-120S-E














Reviews: