manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

The NXP Semiconductors SAFE ASSURE Qorivva MPC5601P is a cutting-edge automotive microcontroller, offering unparalleled security features. Gain a comprehensive understanding of its functionalities by accessing the free Reference Manual. Download it now from manualshive.com, the ultimate destination for user manuals. Explore this game-changing product manual and unlock its full potential.

Share
Download
background image

Chapter 20 Deserial Serial Peripheral Interface (DSPI)

MPC5602P Microcontroller Reference Manual, Rev. 4

472

Freescale Semiconductor

 

20.8.5.3

Modified SPI transfer format (MTFE = 1, CPHA = 0)

In this modified transfer format both the master and the slave sample later in the SCK period than in classic 
SPI mode to allow for delays in device pads and board traces. These delays become a more significant 
fraction of the SCK period as the SCK period decreases with increasing baud rates.

NOTE

For the modified transfer format to operate correctly, you must thoroughly 
analyze the SPI link timing budget.

The master and the slave place data on the SOUT_

x

 pins at the assertion of the CS

x

 signal. After the CS

x

 

to SCK_

x

 delay has elapsed the first SCK_

x

 edge is generated. The slave samples the master SOUT_

x

 

signal on every odd numbered SCK_

x

 edge. The slave also places new data on the slave SOUT_

x

 on every 

odd numbered clock edge.

The master places its second data bit on the SOUT_

x

 line one system clock after odd numbered SCK_

x

 

edge. The point where the master samples the slave SOUT_

x

 is selected by writing to the SMPL_PT field 

in the DSPI

x

_MCR. 

Table 20-25

 lists the number of system clock cycles between the active edge of 

SCK_

x

 and the master sample point for different values of the SMPL_PT bit field. The master sample point 

can be delayed by one or two system clock cycles.

Figure 20-18

 shows the modified transfer format for CPHA = 0. Only the condition where CPOL = 0 is 

illustrated. The delayed master sample points are indicated with a lighter shaded arrow.

Table 20-25. Delayed master sample point

SMPL_PT

Number of system clock cycles between odd-numbered edge of SCK

and sampling of SIN

00

0

01

1

10

2

11

Invalid value

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SAFE ASSURE Qorivva MPC5601P

BEIER-Electronic SV1-2-10Z Instruction Manual preview
SV1-2-10Z
Brand: BEIER-Electronic Pages: 22
Elby Designs ASM301-ADSR Diagrams preview
ASM301-ADSR
Brand: Elby Designs Pages: 4
Mitsubishi A1SJ71E71N-B2 User Manual preview
A1SJ71E71N-B2
Brand: Mitsubishi Pages: 30
Trane Technologies BAYSTAT033AC Installation Manual preview
BAYSTAT033AC
Brand: Trane Technologies Pages: 8
R-Tec controlR Installation Manual & User Manual preview
controlR
Brand: R-Tec Pages: 14
NI cRIO-9065 Features preview
cRIO-9065
Brand: NI Pages: 28
Azbil Infilex ZM WY5122 Specifications & Instructions preview
Infilex ZM WY5122
Brand: Azbil Pages: 12
AlfaRadio AlfaSpid RAK Instruction Manual preview
AlfaSpid RAK
Brand: AlfaRadio Pages: 23
Harmonic MediaDirector 2252B Quick Reference Manual preview
MediaDirector 2252B
Brand: Harmonic Pages: 2
ECO POWER AL030W Installation Instructions preview
AL030W
Brand: ECO POWER Pages: 2
Samson 3374 Mounting And Operating Instructions preview
3374
Brand: Samson Pages: 22
Danfoss PVE 4 Series Technical Information preview
PVE 4 Series
Brand: Danfoss Pages: 56
3Ware 720-0104-00 Manual preview
720-0104-00
Brand: 3Ware Pages: 50
SATA air regulator belt plus Operating Instructions Manual preview
air regulator belt plus
Brand: SATA Pages: 158
Resol DeltaSol SLL Installation, Operation, Maintenance Manual preview
DeltaSol SLL
Brand: Resol Pages: 60
ICP DAS USA ISaGRAF VP-23W7 User Manual preview
ISaGRAF VP-23W7
Brand: ICP DAS USA Pages: 192
RNA ESK 2002 Operating Instructions Manual preview
ESK 2002
Brand: RNA Pages: 23
Texas Instruments Hercules TMS570LS31x User Manual preview
Hercules TMS570LS31x
Brand: Texas Instruments Pages: 26

Brands by name

Popular brands

Load more brands