NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

Share

Page: 241 / 954

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P Reference Manual Download Page 241

Chapter 11 System Integration Unit Lite (SIUL)

MPC5602P Microcontroller Reference Manual, Rev. 4

Freescale Semiconductor

241

•

System configuration
— Pad configuration control

11.3.1

Register protection

Most of the configuration registers of the System Integration Unit Lite are protected from accidental
writes, see

Appendix A, “Registers Under Protection

11.4

External signal description

The pad configuration allows flexible, centralized control of the pin electrical characteristics of the MCU
with the GPIO control providing centralized general purpose I/O for an MCU that multiplexes GPIO with
other signals at the I/O pads. These other signals, or alternate functions, will normally be the peripherals
functions. The internal multiplexing allows user selection of the input to chip-level signal multiplexers.
Each GPIO port communicates via 16 I/O channels. In order to use the pad as a GPIO, the corresponding
Pad Configuration Registers (PCR[0:71]) for all pads used in the port must be configured as GPIO rather
than as the alternate pad function.

lists the external pins used by the SIUL.

(

11.4.1

Detailed signal descriptions

11.4.1.1

General-purpose I/O pins (GPIO[0:66])

The GPIO pins provide general-purpose input and output function. The GPIO pins are generally
multiplexed with other I/O pin functions. Each GPIO input and output is separately controlled by an input
(GPDI

n_n

) or output (GPDO

n_n

) register.

Section 11.5.2.10, “GPIO Pad Data Output registers 0_3–68_71 (GPDO[0_3:68_71])

and

Section 11.5.2.11, “GPIO Pad Data Input registers 0_3–68_71 (GPDI[0_3:68_71])

.

11.4.1.2

External interrupt request input pins (EIRQ[0:24])

The EIRQ[0:24] are connected to the SIUL inputs. Rising or falling edge events are enabled by setting the
corresponding bits in the “n” SIUL_IREER or the SIUL_IFEER register. See

Section 11.5.2.5, “Interrupt

Table 11-1. SIUL signal properties

GPIO category

Name

I/O direction

Function

System configuration

GPIO[0:19],

GPIO[22],

GPIO[35:62]

Input/Output

General-purpose input/output

GPIO[23:34],

GPIO[63],

GPIO[65:66]

Input

Analog precise channel pins

External interrupt

EIRQ[0:24]

Input

Pins with External Interrupt Request functionality.
Please refer to the signal description chapter of this
reference manual for details.

«
...
239
240
241
242
243
...
»

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands