manualshive.com logo in svg

NXP Semiconductors PXN2020, Reference Manual, Page: 658 / 1376

Share
Download
NXP Semiconductors PXN2020 Reference Manual Download Page 658

FlexRay Communication Controller (FlexRAY)

PXN20 Microcontroller Reference Manual, Rev. 1

26-44

Freescale Semiconductor

26.5.2.34 Sync Frame ID Rejection Filter Register (SFIDRFR)

This register defines the Sync Frame Rejection Filter ID. The application must update this register outside 
of the static segment. If the application updates this register in the static segment, it can appear that the 
controller accepts the sync frame in the current cycle.

 

OPT

One Pair Trigger — This trigger bit controls whether the controller writes continuously or only one pair of 
Sync Frame Tables into the FlexRay memory. 

If this trigger is set to 1 while SDVEN or SIDEN is set to 1, the controller writes only one pair of the enabled 
Sync Frame Tables corresponding to the next even-odd-cycle pair into the FlexRay memory. In this case, the 
controller clears the SDVEN or SIDEN bits immediately.

If this trigger is set to 0 while SDVEN or SIDEN is set to 1, the controller writes continuously the enabled Sync 
Frame Tables into the FlexRay memory. 
0 Write continuously pairs of enabled Sync Frame Tables into FlexRay memory.
1 Write only one pair of enabled Sync Frame Tables into FlexRay memory.

SDVEN

Sync Frame Deviation Table Enable — This bit controls the generation of the Sync Frame Deviation Tables. 
The application must set this bit to request the controller to write the Sync Frame Deviation Tables into the 
FlexRay memory. 
0 Do not write Sync Frame Deviation Tables.
1 Write Sync Frame Deviation Tables into FlexRay memory.
Note: If SDVEN is set to 1, then SIDEN must also be set to 1.

SIDEN

Sync Frame ID Table Enable — This bit controls the generation of the Sync Frame ID Tables. The 
application must set this bit to 1 to request the controller to write the Sync Frame ID Tables into the FlexRay 
memory.
0 Do not write Sync Frame ID Tables.
1 Write Sync Frame ID Tables into FlexRay memory. 

Base + 0x0046

16-bit write access required

Write: Normal Mode

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

0

0

0

0

0

0

SYNFRID

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Figure 26-34. Sync Frame ID Rejection Filter Register (SFIDRFR)

Table 26-40. SFIDRFR Field Descriptions

Field

Description

SYNFRID

Sync Frame Rejection ID — This field defines the frame ID of a frame that must not be used for clock 
synchronization. For details see 

Section 26.6.15.2, Sync Frame Rejection Filtering.

Table 26-39. SFTCCSR Field Descriptions (continued)

Field

Description

Summary of Contents for PXN2020

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments