manualshive.com logo in svg

NXP Semiconductors PXN2020, Reference Manual, Page: 655 / 1376

Share
Download
NXP Semiconductors PXN2020 Reference Manual Download Page 655

FlexRay Communication Controller (FlexRAY)

PXN20 Microcontroller Reference Manual, Rev. 1

Freescale Semiconductor

26-41

26.5.2.30 System Memory Access Time-Out Register (SYMATOR)

Table 26-35. CIFRR Field Descriptions

Field

Description

MIF

Module Interrupt Flag — This flag is set if there is at least one interrupt source that has its interrupt flag 
asserted.
0 No interrupt source has its interrupt flag asserted.
1 At least one interrupt source has its interrupt flag asserted.

PRIF

Protocol Interrupt Flag — This flag is set if at least one of the individual protocol interrupt flags in the 

Protocol 

Interrupt Flag Register 0 (PIFR0)

 or 

Protocol Interrupt Flag Register 1 (PIFR1)

 is equal to 1.

0 All individual protocol interrupt flags are equal to 0.
1 At least one of the individual protocol interrupt flags is equal to 1.

CHIF

CHI Interrupt Flag — This flag is set if at least one of the individual CHI error flags in the 

CHI Error Flag Register 

(CHIERFR)

 is equal to 1.

0 All CHI error flags are equal to 0.
1 At least one CHI error flag is equal to 1.

WUPIF

Wakeup Interrupt Flag — Provides the same value as GIFER[WUPIF].

FAFBIF

Receive FIFO Channel B Almost Full Interrupt Flag — Provides the same value as GIFER[FAFBIF].

FAFAIF

Receive FIFO Channel A Almost Full Interrupt Flag — Provides the same value as GIFER[FAFAIF].

RBIF

Receive Message Buffer Interrupt Flag — This flag is set if for at least one of the individual receive message 
buffers (MBCCSRn[MTD] = 0) the interrupt flag MBIF in the corresponding 

Message Buffer Configuration, 

Control, Status Registers (MBCCSRn)

 

is equal to 1.

0 None of the individual receive message buffers has the MBIF flag asserted.
1 At least one individual receive message buffers has the MBIF flag asserted.

TBIF

Transmit Message Buffer Interrupt Flag — This flag is set if for at least one of the individual single or double 
transmit message buffers (MBCCSRn[MTD] = 1) the interrupt flag MBIF in the corresponding 

Message Buffer 

Configuration, Control, Status Registers (MBCCSRn)

 is equal to 1.

0 None of the individual transmit message buffers has the MBIF flag asserted.
1 At least one individual transmit message buffers has the MBIF flag asserted.

Base + 0x003E

Write: Disabled Mode

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

0

0

0

0

0

0

0

0

TIMEOUT

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

1

0

0

Figure 26-30. System Memory Access Time-Out Register (SYMATOR)

Table 26-36. SYMATOR Field Descriptions

Field

Description

TIMEOUT

System Memory Access Time-Out — This value defines the maximum amount of time to finish a system bus 
access in order to ensure correct frame transmission and reception (see 

Section 26.6.19.2, System Bus Access 

Timeout

).

Summary of Contents for PXN2020

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments