manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

Share
Download
NXP Semiconductors MSC8113 Reference Manual Download Page 481

Host Access Modes and Timings

MSC8113 Reference Manual, Rev. 0

Freescale Semiconductor

14-21

14.3.4.4   Synchronous Single Read Using Single Strobe Mode

Figure 14-14 shows a synchronous single read access using Single Strobe mode. The DSI 
samples 

HA[11–29]

, 

HDST[0–1]

, 

HCID[0–3]

, 

HDBE[0–7]

, 

HRW

, and 

HBRST

 on the first 

HCLKIN

 rising 

edge on which 

HCS

 is asserted. If the 

HCID[0–3]

 signals match the CHIPID value, the DSI is 

accessed. At least one 

HDBE

 signal must be asserted, 

HRW

 must be high, and 

HBRST

 must be 

deasserted. When the DCR[RPE] bit is set (see page 14-29), read access to the memory space 
(not to the register space) initiates prefetching data from consecutive addresses in the internal 
memory space. Assertion of 

HTA

 indicates that data is valid and that the host must sample the host 

data lines and terminate the access. The 

HTA

 is asserted earlier when the data for this access is 

already prefetched to the read buffer. 

HTA

 is asserted for one 

HCLKIN

 cycle and driven to logic 1 in 

the next cycle. It stops being driven on the next rising edge of 

HCLKIN

. The host can start its next 

access to the same MSC8113 immediately in the next 

HCLKIN

 rising edge without deasserting 

HCS

 

between accesses. If the next access is not to the same MSC8113, then, to prevent contention on 

HTA

, the host must wait to access the next device until the previous DSI stops driving 

HTA

.

 

Figure 14-14.  Synchronous Single Read Using Single Strobe Mode

HCLKIN

HCS

HBRST

 

HTA (output)

HCID[0–3]

HD[0–63] (output)

HDBE[0–7]

HA[11–29]

HDST[0–1]

valid value

valid value

valid value

valid value

don’t care

don’t care

don’t care

don’t care

don’t

care

don’t care

don’t care

don’t care

don’t care

don’t care

don’t care

don’t care

HRW

don’t care

don’t care

Note: The signal timing shown for HDBE[0–7] is for signals that are asserted. Unused signals remain high (deasserted).

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands