manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

Share
Download
NXP Semiconductors MSC8113 Reference Manual Download Page 473

Host Access Modes and Timings

MSC8113 Reference Manual, Rev. 0

Freescale Semiconductor

14-13

14.3.2.2   DSI Access Modes

The four DSI access modes (Dual Strobe/Single Strobe, Asynchronous/Synchronous) share the 
same DSI external signals with different naming conventions, as listed in Table 14-6.

14.3.3   Asynchronous Mode Operation

This section discusses both asynchronous writes and reads. These examples use 64-bit mode. For 
32-bit mode refer to the enable and strobe signal definitions listed in Table 14-6.

14.3.3.1   Asynchronous Write Using Dual Strobe Mode

Figure 14-7 shows an asynchronous write access using Dual Strobe mode. The DSI samples the 
Host Chip ID signals (

HCID[0–3]

) on the first falling edge of the Host Write Byte Strobe signals 

(

HWBS

) on which the Host Chip Select signal (

HCS

) is asserted. If 

HCID[0–3]

 match the CHIPID 

value, the DSI is accessed. Assertion of the Host Transfer Acknowledge (

HTA

) signal indicates 

that the DSI is ready to sample the host data bus (

HD[0–63]

), and the host can terminate the access 

by deasserting 

HWBS

. 

The DCR[HTAAD] and DCR[HTADT] fields determine which of the following actions the DSI 
takes at end of an access (the rising edge of 

HWBS

):

„

Stop driving 

HTA

. DCR[HTAAD] = 0 and DCR[HTADT] = 00 (no drive time). This mode 

requires a pull-down resistor on 

HTA

.

„

Drive 

HTA

 high. DCR[HTAAD] = 1 and DCR[HTADT] 

≠

 00. The DCR[HTADT] value 

indicates the amount of time to drive 

HTA

. This mode requires a pull-up resistor on 

HTA

.

Table 14-6.  DSI Access Mode Signals 

Access Mode

Strobe Mode

32-Bit Data Bus

64-Bit Data Bus

Read Signals

Write Signals

Read Signals

Write Signals

Asynchronous

Dual

 HRDS

HWBS[0–3] HRDS

HWBS[0–7] 

Asynchronous

Single

HDBS[0–3] and 
HRW

HDBS[0–3] and 
HRW

HDBS[0–7] and 
HRW

HDBS[0–7] and 
HRW

Synchronous

Dual

HRDE

HWBE[0–3] HRDE

HWBE[0–7] 

Synchronous

Single

HDBE[0–3] and 
HRW

HDBE[0–3] and 
HRW

HDBE[0–7] and 
HRW

HDBE[0–7] and 
HRW

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands