manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

Share
Download
NXP Semiconductors MSC8113 Reference Manual Download Page 42

MSC8113 Reference Manual, Rev. 0

1-14

Freescale Semiconductor

MSC8113 Overview

1.2.1.4   QBus System

The QBC is a bus controller that handles internal memory contentions. It snoops the activity on 
the buses connected to the internal memory and freezes the SC140 core and address bus activity. 
It creates the atomic instruction acknowledge to the SC140 core during the reservation process. 
The EQBS enables the SC140 core to communicate with external devices efficiently. It handles 
the switching between the three core buses and the QBus. SC140 core accesses that apply to 
memory space above the internal memory (QBus Base Line = 0x00F00000) are transferred to the 
QBus through the EQBS. The EQBS also connects to the instruction cache and initiates requests 
for cache updates in order to improve the hit ratio. The EQBS operates at the same frequency as 
the SC140 core. The module handles the SC140 core and the instruction cache requests, bringing 
the data on the QBus. As Figure 1-4 shows, the EQBS consists of a bus switch to handle data 
read operations, a write buffer to handle data write operations, a fetch unit to handle all program 
read operations, a control unit, and the banks to handle the communication with the slaves and all 
EQBS registers. 

Note:

For details, see Section 9.4, Instruction Cache (ICache), on page 9-24.

The QBus masters are the fetch unit, write buffer, and bus switch. The control unit is the arbiter 
for the QBus masters.The bus switch handles all data read above the QBus baseline, write 
operations when the write buffer is disabled, and atomic (read modify write) write operations. 
Read accesses of program (fetch) that are above the QBus baseline occur through the fetch unit. 

Figure 1-4.  EQBS Block Diagram

64 

128 

64 

EQBS

Control

Fetch Unit

Banks

Write Buffer

Multiplexer

Multiplex

I-Cache

Memory

ICache

Valid

Array

Tag

Array

128 

Bus Switch

Data

Address

Registers

EQBS

XA-Bus

XB-Bus

P-Bus

QBus

Unit 

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands