manualshive.com logo in svg

NXP Semiconductors MPC5644A, Reference Manual, Page: 1530 / 1735

Share
Download
NXP Semiconductors MPC5644A Reference Manual Download Page 1530

FlexRay Communication Controller (FlexRay)

MPC5644A Microcontroller Reference Manual, Rev. 6

1530

Freescale Semiconductor

 

.

NOTE

If at least one message buffer assigned to a certain slot is assigned to both 
channels, then all message buffers assigned to this slot have to be assigned 
to both channels. Otherwise, the message buffer configuration is illegal and 
the result of the message buffer search is not defined.

33.5.2.80 Message Buffer Frame ID Registers (FR_MBFIDRn)

Table 33-90. FR_MBCCFRn field description

Field

Description

MTM

Message Buffer Transmission Mode

 — This control bit applies only to transmit message buffers and 

defines the transmission mode.
0 Event transmission mode
1 State transmission mode

CHA
CHB

Channel Assignment 

— These control bits define the channel assignment and control the receive and 

transmit behavior of the message buffer according to 

Table 33-91

.

CCFE

Cycle Counter Filtering Enable

 — This control bit is used to enable and disable the cycle counter 

filtering.
0 Cycle counter filtering disabled
1 Cycle counter filtering enabled 

CCFMSK

Cycle Counter Filtering Mask 

— This field defines the filter mask for the cycle counter filtering.

CCFVAL

Cycle Counter Filtering Value

 — This field defines the filter value for the cycle counter filtering.

Table 33-91. Channel assignment description

CHA CHB

Transmit message buffer

Receive message buffer

Static segment

Dynamic segment

Static segment

Dynamic segment

1

1

transmit on both 
channel A and 
channel B

Reserved (function not 
available)

store first valid frame 
received on either 
channel A or channel B

Reserved (function not 
available) 

0

1

transmit on channel B

transmit on channel B

store first valid frame 
received on channel B

store first valid frame 
received on channel B

1

0

transmit on channel A

transmit on channel A

store first valid frame 
received on channel A

store first valid frame 
received on channel A

0

0

no frame transmission

no frame transmission

no frame stored

no frame stored

Base + 0x0104 (FR_MBFIDR0)
Base + 0x010C (FR_MBFIDR1)
...
Base + 0x04FC (FR_MBFIDR127)

16-bit write access required

Write: 

POC:config

 or MB_DIS

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

0

0

0

0

0

FID

W

Reset

0

0

0

0

0

–

–

–

–

–

–

–

–

–

–

–

Figure 33-111. Message Buffer Frame ID Registers (FR_MBFIDRn)

Summary of Contents for MPC5644A








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments