NXP Semiconductors MPC5644A Reference Manual Download Page 1511

Page: 1511 / 1735

FlexRay Communication Controller (FlexRay)

MPC5644A Microcontroller Reference Manual, Rev. 6

Freescale Semiconductor

1511

33.5.2.66 Receive FIFO Range Filter Control Register (FR_RFRFCTR)

This register is used to enable and disable each frame ID range filter and to define whether it is running as
acceptance or rejection filter.

33.5.2.67 Last Dynamic Transmit Slot Channel A Register (FR_LDTXSLAR)

Base + 0x009A

Write: Anytime

F3MD

F2MD

F1MD

F0MD

Reset

Figure 33-67. Receive FIFO Range Filter Control Register (FR_RFRFCTR)

Table 33-75. FR_RFRFCTR field description

Field

Description

F3MD

Range Filter 3 Mode

— This control bit defines the filter mode of the frame ID range filter 3.

0 range filter 3 runs as acceptance filter
1 range filter 3 runs as rejection filter

F2MD

Range Filter 2 Mode

— This control bit defines the filter mode of the frame ID range filter 2.

0 range filter 2 runs as acceptance filter
1 range filter 2 runs as rejection filter

F1MD

Range Filter 1 Mode

— This control bit defines the filter mode of the frame ID range filter 1.

0 range filter 1 runs as acceptance filter
1 range filter 1 runs as rejection filter

F0MD

Range Filter 0 Mode

— This control bit defines the filter mode of the frame ID range filter 0.

0 range filter 0 runs as acceptance filter
1 range filter 0 runs as rejection filter

F3EN

Range Filter 3 Enable

— This control bit is used to enable and disable the frame ID range filter 3.

0 range filter 3 disabled
1 range filter 3 enabled

F2EN

Range Filter 2 Enable

— This control bit is used to enable and disable the frame ID range filter 2.

0 range filter 2 disabled
1 range filter 2 enabled

F1EN

Range Filter 1 Enable

— This control bit is used to enable and disable the frame ID range filter 1.

0 range filter 1 disabled
1 range filter 1 enabled

F0EN

Range Filter 0 Enable

— This control bit is used to enable and disable the frame ID range filter 0.

0 range filter 0 disabled
1 range filter 0 enabled

Base + 0x009C

LASTDYNTXSLOTA

Reset

Figure 33-68. Last Dynamic Transmit Slot Channel A Register (FR_LDTXSLAR)

«
...
1509
1510
1511
1512
1513
...
»

Summary of Contents for MPC5644A








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MPC5644A

Reviews:

NXP Semiconductors MPC5644A, Reference Manual, Page: 1511 / 1735

Search results

Summary of Contents for MPC5644A

Reviews: