manualshive.com logo in svg

NXP Semiconductors MPC5566, Reference Manual

Share
Download
NXP Semiconductors MPC5566 Reference Manual Download Page 1086

IEEE 1149.1 Test Access Port Controller (JTAGC)

MPC5566 Microcontroller Reference Manual, Rev. 2

Freescale Semiconductor

24-5

 

24.3.2

Bypass Register

The bypass register is a single-bit shift register path selected for serial data transfer between TDI and TDO 
when the BYPASS, CLAMP, HIGHZ or reserve instructions are active. After entry into the capture-DR 
state, the single-bit shift register is set to a logic 0. Therefore, the first bit shifted out after selecting the 
bypass register is always a logic 0.

24.3.3

Device Identification Register

The device identification register, shown in 

Figure 24-3

, allows the part revision number, design center, 

part identification number, and manufacturer identity code to be determined through the TAP. The device 
identification register is selected for serial data transfer between TDI and TDO when the IDCODE 
instruction is active. Entry into the capture-DR state while the device identification register is selected 
loads the IDCODE into the shift register to be shifted out on TDO in the Shift-DR state. No action occurs 
in the update-DR state.

24.3.4

Boundary Scan Register

The boundary scan register is connected between TDI and TDO when the EXTEST, SAMPLE or 
SAMPLE/PRELOAD instructions are active. It is used to capture input pin data, force fixed values on 
output pins, and select a logic value and direction for bidirectional pins. Each bit of the boundary scan 
register represents a separate boundary scan register cell, as described in the IEEE 1149.1-2001 standard 
and discussed in 

Section 24.4.5, “Boundary Scan

.” The size of the boundary scan register is 480 bits.

IR[4:0]: 0_0001 (IDCODE)

Access: R/O

0

1

2

3

4

5

6

7

8

9

10 11

12

13 14

15

16 17

18

19 20

21

22 23

24

25 26

27

28 29

30

31

R

PRN

DC

PIN

MIC

ID

W

Reset 0

0

0

0

1

0

0

0

0

0

0

1

0

1

1

0

0

1

1

0

0

0

0

0

0

0

0

1

1

1

0

1

Figure 24-3. Device Identification Register

Table 24-2. Device Identification Register Field Descriptions

Field

Description

0–3

PRN

Part revision number. Contains the revision number of the device. This field changes with each revision of the device 
or module.

4–9

DC

Design center. Indicates the Freescale design center. For the MPC5566 this value is 0x20. 

10–19

PIN

Part identification number. Contains the part number of the device. For the MPC5566, this value is 0x166. 

20–30

MIC

Manufacturer identity code. Contains the reduced Joint Electron Device Engineering Council (JEDEC) ID for 
Freescale, 0xE.

31

ID

IDCODE register ID. Identifies this register as the device identification register and not the bypass register. Always 
set to 1.

Summary of Contents for MPC5566





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands