manualshive.com logo in svg

NXP Semiconductors MKL27Z128VFM4, Reference Manual

Share
Download
NXP Semiconductors MKL27Z128VFM4 Reference Manual Download Page 557

33.5.21 USB Transceiver Control register 0 (USBx_USBTRC0)

Includes signals for basic operation of the on-chip USB Full Speed transceiver and
configuration of the USB data connection that are not otherwise included in the USB Full
Speed controller registers.

Address: 4007_2000h base + 10Ch offset = 4007_210Ch

Bit

7

6

5

4

Read

USBRESMEN

0

Write

USBRESET

1

Reset

0

0

0

0

Bit

3

2

1

0

Read

0

USB_CLK_

RECOVERY_INT

SYNC_DET

USB_RESUME_INT

Write

Reset

0

0

0

0

USBx_USBTRC0 field descriptions

Field

Description

7

USBRESET

USB Reset

Generates a hard reset to USB. After this bit is set and the reset occurs, this bit is automatically cleared.

NOTE: This bit is always read as zero. Wait two USB clock cycles after setting this bit.

0

Normal USB module operation.

1

Returns the USB module to its reset state.

6

Reserved

This field is reserved.

NOTE: Software must set this bit to 1b.

5

USBRESMEN

Asynchronous Resume Interrupt Enable

This bit, when set, allows the USB module to send an asynchronous wakeup event to the MCU upon
detection of resume signaling on the USB bus. The MCU then re-enables clocks to the USB module. It is
used for low-power suspend mode when USB module clocks are stopped or the USB transceiver is in
Suspend mode. Async wakeup only works in device mode.

0

USB asynchronous wakeup from suspend mode disabled.

1

USB asynchronous wakeup from suspend mode enabled. The asynchronous resume interrupt differs
from the synchronous resume interrupt in that it asynchronously detects K-state using the unfiltered
state of the D+ and D– pins. This interrupt should only be enabled when the Transceiver is
suspended.

4–3

Reserved

This field is reserved.
This read-only field is reserved and always has the value 0.

Table continues on the next page...

Chapter 33 Universal Serial Bus (USB) FS Subsystem

KL27 Sub-Family Reference Manual , Rev. 5, 01/2016

Freescale Semiconductor, Inc.

557

Summary of Contents for MKL27Z128VFM4












































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands