Home
/
NXP Semiconductors
/
MCF5272 ColdFire
/
User Manual

NXP Semiconductors MCF5272 ColdFire, User Manual, Page: 228 / 545

Share

Page: 228 / 545

NXP Semiconductors MCF5272 ColdFire User Manual Download Page 228

Ethernet Module

MCF5272 ColdFire

®

Integrated Microprocessor User’s Manual, Rev. 3

11-10

Freescale Semiconductor

11.5

Programming Model

This section gives an overview of the registers, followed by a description of the buffers.

The FEC is programmed by a combination of control/status registers (CSRs) and buffer descriptors. The
CSRs are used for mode control and to extract global status information. The descriptors are used to pass
data buffers and related buffer information between the hardware and software.

shows the FEC register memory map with each register address, name, and a brief description.

The following sections describe each register in detail.

Table 11-6. FEC Register Memory Map

Offset

Name

Width

Description

0x840

ECR

32

Ethernet control register

0x844

EIR

32

Interrupt event register

0x848

EIMR

32

Interrupt mask register

0x84C

IVSR

32

Interrupt vector status register

0x850

RDAR

32

Receive descriptor active register

0x854

TDAR

32

Transmit descriptor active register

0x880

MMFR

32

MII management frame register

0x884

MSCR

32

MII speed control register

0x8CC

FRBR

32

FIFO receive bound register

0x8D0

FRSR

32

FIFO receive start register

0x8EC

TFSR

32

FIFO transmit start register

0x8E4

TFWR

32

Transmit FIFO watermark

0x944

RCR

32

Receive control register

0x948

MFLR

32

Maximum frame length register

0x984

TCR

32

Transmit control register

0xC00

MALR

32

Lower 32-bits of MAC address

0xC04

MAUR

32

Upper 16-bits of MAC address

0xC08

HTUR

32

Upper 32-bits of hash table

0xC0C

HTLR

32

Lower 32-bits of hash table

0xC10

ERDSR

32

Pointer to receive descriptor ring

0xC14

ETDSR

32

Pointer to transmit descriptor ring

0xC18

EMRBR

32

Maximum receive buffer size

0xC40–

0xDFF

EFIFO

32

FIFO RAM space

«
...
226
227
228
229
230
...
»

Summary of Contents for MCF5272 ColdFire


































































































































































































































































































































































































































































































































































Reviews:

No comments