NXP Semiconductors MC9S12XS128 Reference Manual Download | Manualshive

Page: 129 / 739

background image

Memory Mapping Control (S12XMMCV4)

S12XS Family Reference Manual, Rev. 1.13

Freescale Semiconductor

129

3.1.3

S12X Memory Mapping

The S12X architecture implements a number of memory mapping schemes including

•

a CPU 8MB global map, defined using a global page (GPAGE) register and dedicated 23-bit
address load/store instructions.

•

a BDM 8MB global map, defined using a global page (BDMGPR) register and dedicated 23-bit
address load/store instructions.

•

a (CPU or BDM) 64KB local map, defined using specific resource page (RPAGE, EPAGE and
PPAGE) registers and the default instruction set. The 64KB visible at any instant can be considered
as the local map accessed by the 16-bit (CPU or BDM) address.

The MMC module performs translation of the different memory mapping schemes to the specific global
(physical) memory implementation.

3.1.4

Modes of Operation

This subsection lists and briefly describes all operating modes supported by the MMC.

3.1.4.1

Power Saving Modes

•

Run mode

MMC is functional during normal run mode.

•

Wait mode

MMC is functional during wait mode.

•

Stop mode

MMC is inactive during stop mode.

3.1.4.2

Functional Modes

•

Single chip modes

In normal and special single chip mode the internal memory is used.

3.1.5

Block Diagram

shows a block diagram of the MMC.

«
...
127
128
129
130
131
...
»

Summary of Contents for MC9S12XS128




































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MC9S12XS128

Brand: TCS Basys Controls Pages: 2

MorphoAccess SIGMA Extreme Series

Brand: Safran Pages: 79

Brand: Lawler Pages: 5

Brand: Parker Pages: 21

Brand: Parker Pages: 26

Brand: Vageo Pages: 2

Brand: U.S. Divers Pages: 22

PowerFlex 755 IP00

Brand: Allen-Bradley Pages: 78

Brand: NXP Semiconductors Pages: 20

Brand: Zencontrol Pages: 2

Brand: Daikin Pages: 2

Brand: Advantech Pages: 3

Brand: Eaton Pages: 2

Brand: Linear Technology Pages: 5

Brand: Beckhoff Pages: 67

Brand: Omron Pages: 12

Integrated Controller Rev C EZ-ZONE PM

Brand: Watlow Pages: 80

DMX-LED-DIMMER X9 HR

Brand: DMX4ALL Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands