manualshive.com logo in svg

NXP Semiconductors MC9S08PA4, Reference Manual

Share
Download
NXP Semiconductors MC9S08PA4 Reference Manual Download Page 72

4.5.2.8.3 Allowed simultaneous flash and EEPROM operations

Only the operations marked 'OK' in the following table are permitted to be run
simultaneously on the flash and EEPROM blocks. Some operations cannot be executed
simultaneously because certain hardware resources are shared by the two memories. The
priority has been placed on permitting flash reads while program and erase operations
execute on the EEPROM, providing read (flash) while write (EEPROM) functionality.

Table 4-18. Allowed simultaneous flash and EEPROM operations

Program flash

EEPROM

Read

Margin read

Program

Sector erase

Mass erase

Read

OK

OK

OK

Margin Read

1

Program

Sector Erase

Mass Erase

2

OK

1. A 'Margin read' is any read after executing the margin setting commands 'Set user margin level' or 'Set field margin level'

with anything but the 'normal' level specified. See the Note on margin settings in

2. The 'Mass erase' operations are commands 'Erase all blocks' and 'Erase flash block'

4.5.2.9 Flash and EEPROM command summary

This section provides details of all available flash commands launched by a command
write sequence. The FSTAT[ACCERR] bit will be set during the command write
sequence if any of the following illegal steps are performed, causing the command not to
be processed by the memory controller:

• Starting any command write sequence that programs or erases flash memory before

initializing the FLCKDIV register.

• Writing an invalid command as part of the command write sequence.

• For additional possible errors, refer to the error handling table provided for each

command.

If a flash block is read during the execution of an algorithm (FSTAT[CCIF] = 0) on that
same block, the read operation will return invalid data if both flags FERSTAT[SFDIF]
and FERSTAT[DFDIF] are set. If the FERSTAT[SFDIF] or FERSTAT[DFDIF] flags
were not previously set when the invalid read operation occurred, both the
FERSTAT[SFDIF] and FERSTAT[DFDIF] flags will be set.

If the FSTAT[ACCERR] or FSTAT[FPVIOL] bits are set, the user must clear these bits
before starting any command write sequence.

Flash and EEPROM

MC9S08PA4 Reference Manual, Rev. 5, 08/2017

72

NXP Semiconductors

Summary of Contents for MC9S08PA4


















































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands