manualshive.com logo in svg

NXP Semiconductors MC9S08PA4, Reference Manual

The NXP Semiconductors MC9S08PA4 is a powerful microcontroller offering exceptional performance and versatility. To maximize your understanding and effectively utilize its features, we provide a comprehensive Reference Manual available for free download at manualshive.com, offering detailed instructions and guidelines for optimal usage.

Share
Download
background image

BKGD is a pseudo-open-drain pin and there is an on-chip pullup so no external pullup
resistor is required. Unlike typical open-drain pins, the external RC time constant on this
pin, which is influenced by external capacitance, plays almost no role in signal rise time.
The custom protocol provides for brief, actively driven speedup pulses to force rapid rise
times on this pin without risking harmful drive level conflicts. Refer to 

Communication

details

 for more detail.

When no debugger pod is connected to the 6-pin BDM interface connector, the internal
pullup on BKGD chooses normal operating mode. When a debug pod is connected to
BKGD it is possible to force the MCU into active background mode after reset. The
specific conditions for forcing active background depend upon the HCS08 derivative
(refer to the introduction to this Development Support section). It is not necessary to reset
the target MCU to communicate with it through the background debug interface.

18.2.2 Communication details

The BDC serial interface requires the external controller to generate a falling edge on the
BKGD pin to indicate the start of each bit time. The external controller provides this
falling edge whether data is transmitted or received.

BKGD is a pseudo-open-drain pin that can be driven either by an external controller or
by the MCU. Data is transferred MSB first at 16 BDC clock cycles per bit (nominal
speed). The interface times out if 512 BDC clock cycles occur between falling edges
from the host. Any BDC command that was in progress when this timeout occurs is
aborted without affecting the memory or operating mode of the target MCU system.

The custom serial protocol requires the debug pod to know the target BDC
communication clock speed.

The clock switch (CLKSW) control bit in the BDC status and control register allows the
user to select the BDC clock source. The BDC clock source can either be the bus or the
alternate BDC clock source.

The BKGD pin can receive a high or low level or transmit a high or low level. The
following diagrams show timing for each of these cases. Interface timing is synchronous
to clocks in the target BDC, but asynchronous to the external host. The internal BDC
clock signal is shown for reference in counting cycles.

The following figure shows an external host transmitting a logic 1 or 0 to the BKGD pin
of a target HCS08 MCU. The host is asynchronous to the target so there is a 0-to-1 cycle
delay from the host-generated falling edge to where the target perceives the beginning of
the bit time. Ten target BDC clock cycles later, the target senses the bit level on the
BKGD pin. Typically, the host actively drives the pseudo-open-drain BKGD pin during

Background debug controller (BDC)

MC9S08PA4 Reference Manual, Rev. 5, 08/2017

354

NXP Semiconductors

Summary of Contents for MC9S08PA4


















































































































































































































































































































































































































Reviews:

No comments

Related manuals for MC9S08PA4

Baccara G75-DFC Installation Operation & Maintenance preview
G75-DFC
Brand: Baccara Pages: 16
M-system SC100 Series Applications Manual preview
SC100 Series
Brand: M-system Pages: 103
M-system MSP40 Instruction Manual preview
MSP40
Brand: M-system Pages: 18
YOKOGAWA TC 10-L Engineering Manual preview
TC 10-L
Brand: YOKOGAWA Pages: 20
YOKOGAWA UTAdvanced UT32A Technical Information preview
UTAdvanced UT32A
Brand: YOKOGAWA Pages: 3
Trane Technologies BAYSTAT033AC Installation Manual preview
BAYSTAT033AC
Brand: Trane Technologies Pages: 8
Netro SPRITE Quick Start Manual preview
SPRITE
Brand: Netro Pages: 14
Watlow Ramping and Profiling Microprocessor-Based Control SERIES 1500 User Manual preview
Ramping and Profiling Microprocessor-Based Control SERIES 1500
Brand: Watlow Pages: 90
Teradek CTRL.1 Quick Start Manual preview
CTRL.1
Brand: Teradek Pages: 10
Samson Graphite MF8 Quick Start Manual preview
Graphite MF8
Brand: Samson Pages: 64
SystemAir NOTUS-R Installation, Maintenance And Operation Instructions preview
NOTUS-R
Brand: SystemAir Pages: 4
SMSC USB2250 Datasheet preview
USB2250
Brand: SMSC Pages: 35
Air Torque AT1001U Maintenance Manual preview
AT1001U
Brand: Air Torque Pages: 11
alpro EB1001 Instructions preview
EB1001
Brand: alpro Pages: 2
Raytel LLC AR-727H Technical Manual preview
AR-727H
Brand: Raytel LLC Pages: 69
Smartgen HMU8-860 User Manual preview
HMU8-860
Brand: Smartgen Pages: 50
MRMC MRMC-2261-00 Quick Start Manual preview
MRMC-2261-00
Brand: MRMC Pages: 24
ST STEVAL-BFA001V1B Getting Started Manual preview
STEVAL-BFA001V1B
Brand: ST Pages: 30

Brands by name

Popular brands

Load more brands