NXP Semiconductors LPC5411 Series Product Data Sheet Download Page 47

Page: 47 / 105

LPC5411x

All information provided in this document is subject to legal disclaimers.

Product data sheet

Rev. 2.1 — 9 May 2018

47 of 105

NXP Semiconductors

LPC5411x

32-bit ARM Cortex-M4/M0+ microcontroller

[8]

An ADC input voltage above 3.6 V can be applied for a short time without leading to immediate, unrecoverable failure. Accumulated
exposure to elevated voltages at 4.6 V must be less than 10

s total over the lifetime of the device. Applying an elevated voltage to the

ADC inputs for a long time affects the reliability of the device and reduces its lifetime.

[9]

It is recommended to connect an overvoltage protection diode between the analog input pin and the voltage supply pin.

[10] Dependent on package type.

9. Thermal

characteristics

The average chip junction temperature, T

(



C), can be calculated using the following

equation:

(1)

•

amb

= ambient temperature (



C),

•

th(j-a)

= the package junction-to-ambient thermal resistance (



C/W)

•

= sum of internal and I/O power dissipation

The internal power dissipation is the product of I

and V

. The I/O power dissipation of

the I/O pins is often small and many times can be negligible. However it can be significant
in some applications.

Table 11.

Thermal resistance

Symbol Parameter

Conditions

Max/Min

Unit

LQFP64 Package

th(j-a)

thermal resistance from
junction to ambient

JEDEC (4.5 in



4 in); still air



15 %



C/W

Single-layer (4.5 in



3 in); still air 81



15 %



C/W

th(j-c)

thermal resistance from
junction to case



15 %



C/W

WLCSP49 Package

th(j-a)

thermal resistance from
junction to ambient

JEDEC (4.5 in



4 in); still air



15 %



C/W

th(j-c)

thermal resistance from
junction to case

0.3



15 %



C/W

amb

th j

–











Summary of Contents for LPC5411 Series










































































































Search results

Summary of Contents for LPC5411 Series

Reviews:

Related manuals for LPC5411 Series

Brands by name

Popular brands

NXP Semiconductors LPC5411 Series, Product Data Sheet

Search results

Summary of Contents for LPC5411 Series

Reviews:

Related manuals for LPC5411 Series

Brands by name

Popular brands