manualshive.com logo in svg

NXP Semiconductors LPC5410x, User Manual, Page: 15 / 463

Share
Download
NXP Semiconductors LPC5410x User Manual Download Page 15

UM10850

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 2.4 — 13 September 2016 

15 of 464

 

3.1  How to read this chapter

Available interrupt sources may vary with specific LPC5410x device type.

3.2 Features

•

Nested Vectored Interrupt Controller that is an integral part of each CPU.

•

Tightly coupled interrupt controller provides low interrupt latency.

•

Controls system exceptions and peripheral interrupts.

•

The NVIC of the Cortex-M4 supports:.

–

37 vectored interrupts.

–

8 programmable interrupt priority levels with hardware priority level masking.

–

Vector table offset register VTOR.

–

Software interrupt generation.

•

The Cortex- M0+ (present on LPC54102 devices) supports: the first 32 interrupts.

–

32 vectored interrupts.

–

4 programmable interrupt priority levels with hardware priority level masking.

–

Vector table offset register VTOR.

•

Support for NMI from any interrupt (see 

Section 4.5.3

).

3.3 General description

The tight coupling to the NVIC to the CPU allows for low interrupt latency and efficient 
processing of late arriving interrupts.

3.3.1 Interrupt sources

Table 2

 lists the interrupt sources for each peripheral function. Each peripheral device 

may have one or more interrupt lines to the Vectored Interrupt Controller. Each line may 
represent more than one interrupt source. The interrupt number does not imply any 
interrupt priority.

See 

Ref. 1 “Cortex-M4 TRM”

 and 

Ref. 2 “Cortex-M0+ TRM”

 for detailed descriptions of 

the NVIC and the NVIC registers.

 

UM10850

Chapter 3: LPC5410x Nested Vectored Interrupt Controller 
(NVIC)

Rev. 2.4 — 13 September 2016

User manual

Table 2.

Connection of interrupt sources to the NVIC

Interrupt

Name

Description

Flags

0

WDT

Windowed watchdog timer interrupt

WARNINT - watchdog warning interrupt

1

BOD

BOD interrupt

BODINTVAL - BOD interrupt level

2

(reserved)

-

-

3

DMA

DMA interrupts

Interrupt A and interrupt B, error interrupt

Summary of Contents for LPC5410x
















































































































































































































































































































































































































































































Reviews:

No comments