NXP Semiconductors LPC1102 User Manual Download

Page: 220 / 258

UM10429

All information provided in this document is subject to legal disclaimers.

User manual

Rev. 1 — 20 October 2010

220 of 258

NXP Semiconductors

UM10429

Chapter 19: Appendix LPC1102 ARM Cortex-M0 reference

•

For BX and BLX, bit[0] of

must be 1 for correct execution. Bit[0] is used to update

the EPSR T-bit and is discarded from the target address.

Remark:

cond

is the only conditional instruction on the Cortex-M0 processor.

19.4.6.1.4

Condition flags

These instructions do not change the flags.

19.4.6.1.5

Examples

loopA

; Branch to loopA

funC

; Branch with link (Call) to function funC, return address

; stored in LR

; Return from function call

BLX

; Branch with link and exchange (Call) to a address stored

; in R0

BEQ

labelD ; Conditionally branch to labelD if last flag setting

; instruction set the Z flag, else do not branch.

19.4.7 Miscellaneous instructions

Table 211

shows the remaining Cortex-M0 instructions:

Table 211. Miscellaneous instructions

Mnemonic

Brief description

See

BKPT

Breakpoint

Section 19–19.4.7.
1

CPSID

Change Processor State, Disable Interrupts

Section 19–19.4.7.
2

CPSIE

Change Processor State, Enable Interrupts

Section 19–19.4.7.
2

DMB

Data Memory Barrier

Section 19–19.4.7.
3

DSB

Data Synchronization Barrier

Section 19–19.4.7.
4

ISB

Instruction Synchronization Barrier

Section 19–19.4.7.
5

MRS

Move from special register to register

Section 19–19.4.7.
6

MSR

Move from register to special register

Section 19–19.4.7.
7

NOP

No Operation

Section 19–19.4.7.
8

SEV

Send Event

Section 19–19.4.7.
9

Summary of Contents for LPC1102



































































































































































































































































Search results

Summary of Contents for LPC1102

Reviews:

Related manuals for LPC1102

Brands by name

Popular brands

NXP Semiconductors LPC1102, User Manual

Search results

Summary of Contents for LPC1102

Reviews:

Related manuals for LPC1102

Brands by name

Popular brands