NXP Semiconductors LPC1102 User Manual Download | Manualshive

Page: 144 / 258

background image

UM10429

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2010. All rights reserved.

User manual

Rev. 1 — 20 October 2010

144 of 258

NXP Semiconductors

UM10429

Chapter 16: LPC1102 Analog-to-Digital Converter (ADC)

16.6.3 A/D Status Register

The A/D Status register allows checking the status of all A/D channels simultaneously.
The DONE and OVERRUN flags appearing in the ADDRn register for each A/D channel
are mirrored in ADSTAT. The interrupt flag (the logical OR of all DONE flags) is also found
in ADSTAT.

16.6.4 A/D Interrupt Enable Register

This register allows control over which A/D channels generate an interrupt when a
conversion is complete. For example, it may be desirable to use some A/D channels to
monitor sensors by continuously performing conversions on them. The most recent
results are read by the application program whenever they are needed. In this case, an
interrupt is not desirable at the end of each conversion for some A/D channels.

29:27 Unused

These bits always read as zeroes. They could be used for expansion of
the CHN field in future compatible A/D converters that can convert more
channels.

0

30

OVERR
UN

This bit is 1 in burst mode if the results of one or more conversions was
(were) lost and overwritten before the conversion that produced the
result in the V_VREF bits.

0

31

DONE

This bit is set to 1 when an A/D conversion completes. It is cleared
when this register is read and when the ADCR is written. If the ADCR is
written while a conversion is still in progress, this bit is set and a new
conversion is started.

0

Table 142. A/D Global Data Register (AD0GDR - address 0x4001 C004) bit description

Bit

Symbol

Description

Reset
Value

Table 143. A/D Status Register (AD0STAT - address 0x4001 C030) bit description

Bit

Symbol

Description

Reset
Value

4:0

Done4:0

These bits mirror the DONE status flags that appear in the result
register for each A/D channel.

0

7:5

-

Reserved

-

12:8

Overrun7:0 These bits mirror the OVERRRUN status flags that appear in the

result register for each A/D channel. Reading ADSTAT allows
checking the status of all A/D channels simultaneously.

0

15:13 -

Reserved

-

16

ADINT

This bit is the A/D interrupt flag. It is one when any of the individual
A/D channel Done flags is asserted and enabled to contribute to the
A/D interrupt via the ADINTEN register.

0

31:17 Unused

Unused, always 0.

0

«
...
142
143
144
145
146
...
»

Summary of Contents for LPC1102



































































































































































































































































Reviews:

No comments

Related manuals for LPC1102

Brand: Zeagle Pages: 37

Brand: RadioMaster Pages: 49

Brand: ZKTeco Pages: 20

Brand: ZKTeco Pages: 8

Brand: ZKTeco Pages: 10

Brand: ZKTeco Pages: 121

Brand: ZKTeco Pages: 12

Brand: ZKTeco Pages: 6

Brand: ZiLOG Pages: 12

Bell & Gossett Technologic PPS

Brand: Xylem Pages: 20

Brand: Eaton Pages: 2

Brand: Z-Wave Pages: 27

Brand: Pro-face Pages: 48

Brand: C Prox Ltd Pages: 9

Brand: Danfoss Pages: 12

1200-RD00-00-0 Series

Brand: gefran Pages: 6

FINGER007 Series

Brand: IDTECK Pages: 9

Brand: MDT Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands