NXP Semiconductors Kinetis KE1xZ256 Reference Manual Download Page 1157 | Manualshive

Page: 1157 / 1325

background image

LPI2Cx_SCFGR2 field descriptions

Field

Description

31–28

Reserved

This field is reserved.
This read-only field is reserved and always has the value 0.

27–24

FILTSDA

Glitch Filter SDA

Configures the I2C slave digital glitch filters for SDA input, a configuration of 0 will disable the glitch filter.
Glitches equal to or less than FILTSDA cycles long will be filtered out and ignored. The latency through
the glitch filter is equal to 3 cycles and must be configured less than the minimum SCL low or
high period.

The glitch filter cycle count is not affected by the PRESCALE configuration, and is disabled in high speed
mode.

23–20

Reserved

This field is reserved.
This read-only field is reserved and always has the value 0.

19–16

FILTSCL

Glitch Filter SCL

Configures the I2C slave digital glitch filters for SCL input, a configuration of 0 will disable the glitch filter.
Glitches equal to or less than FILTSCL cycles long will be filtered out and ignored. The latency through the
glitch filter is equal to 3 cycles and must be configured less than the minimum SCL low or high
period.

The glitch filter cycle count is not affected by the PRESCALE configuration, and is disabled in high speed
mode.

15–14

Reserved

This field is reserved.
This read-only field is reserved and always has the value 0.

13–8

DATAVD

Data Valid Delay

Configures the SDA data valid delay time for the I2C slave equal to 3 cycles. This
data valid delay must be configured to less than the minimum SCL low period.

The I2C slave data valid delay time is not affected by the PRESCALE configuration, and is disabled in
high speed mode.

7–4

Reserved

This field is reserved.
This read-only field is reserved and always has the value 0.

CLKHOLD

Clock Hold Time

Configures the minimum clock hold time for the I2C slave, when clock stretching is enabled. The minimum
hold time is equal to 3 cycles. The I2C slave clock hold time is not affected by the PRESCALE
configuration, and is disabled in high speed mode.

45.3.24 Slave Address Match Register (LPI2Cx_SAMR)

Address: Base a 140h offset

Bit

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

R

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Bit

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

R

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Chapter 45 Low Power Inter-Integrated Circuit (LPI2C)

Kinetis KE1xZ256 Sub-Family Reference Manual, Rev. 3, 07/2018

NXP Semiconductors

1157

«
...
1155
1156
1157
1158
1159
...
»

Summary of Contents for Kinetis KE1xZ256














































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Kinetis KE1xZ256

ControlMaster CM15

Brand: ABB Pages: 4

Brand: Datalogic Pages: 15

Brand: Samson Pages: 124

Brand: Samson Pages: 86

Brand: VAC Pages: 5

Brand: Lab.gruppen Pages: 2

Brand: Purmo Pages: 2

Brand: salmson Pages: 78

Brand: D+H Pages: 16

Brand: Joy-it Pages: 7

Brand: YASKAWA Pages: 12

Brand: Instrutech Pages: 42

Brand: TDSi Pages: 71

Brand: Azbil Pages: 68

Brand: Ltech Pages: 2

Triad Controls WE Series

Brand: A-T Controls Pages: 13

Brand: Texas Instruments Pages: 19

Brand: Bardac Pages: 235

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands