manualshive.com logo in svg

NXP Semiconductors Kinetis KE1xZ256, Reference Manual

The NXP Semiconductors Kinetis KE1xZ256 is a high-performance microcontroller ideal for a wide range of embedded applications. For comprehensive guidance on using this powerful device, download the Reference Manual for free from the official NXP website. Access detailed instructions and specifications to optimize your project's performance.

Share
Download
background image

LPI2Cx_MSR field descriptions

Field

Description

31–26

Reserved

This field is reserved.
This read-only field is reserved and always has the value 0.

25

BBF

Bus Busy Flag

0

I2C Bus is idle.

1

I2C Bus is busy.

24

MBF

Master Busy Flag

0

I2C Master is idle.

1

I2C Master is busy.

23–15

Reserved

This field is reserved.
This read-only field is reserved and always has the value 0.

14

DMF

Data Match Flag

Indicates that the received data has matched the MATCH0 and/or MATCH1 fields as configured by
MATCFG. Received data that is discarded due to CMD field does not cause this flag to set.

0

Have not received matching data.

1

Have received matching data.

13

PLTF

Pin Low Timeout Flag

Will set when the SCL and/or SDA input is low for more than PINLOW cycles, even when the LPI2C
master is idle. Software is responsible for resolving the pin low condition. This flag cannot be cleared for
as long as the pin low timeout continues and must be cleared before the LPI2C can initiate a START
condition.

0

Pin low timeout has not occurred or is disabled.

1

Pin low timeout has occurred.

12

FEF

FIFO Error Flag

Detects an attempt to send or receive data without first generating a (repeated) START condition. This can
occur if the transmit FIFO underflows when the AUTOSTOP bit is set. When this flag is set, the LPI2C
master will send a STOP condition (if busy) and will not initiate a new START condition until this flag has
been cleared.

0

No error.

1

Master sending or receiving data without START condition.

11

ALF

Arbitration Lost Flag

This flag will set if the LPI2C master transmits a logic one and detects a logic zero on the I2C bus, or if it
detects a START or STOP condition while it is transmitting data. When this flag sets, the LPI2C master will
release the bus (go idle) and will not initiate a new START condition until this flag has been cleared.

0

Master has not lost arbitration.

1

Master has lost arbitration.

10

NDF

NACK Detect Flag

This flag will set if the LPI2C master detects a NACK when transmitting an address or data. If a NACK is
expected for a given address (as configured by the command word) then the flag will set if a NACK is not
generated. When set, the master will transmit a STOP condition and will not initiate a new START
condition until this flag has been cleared.

Table continues on the next page...

Memory Map and Registers

Kinetis KE1xZ256 Sub-Family Reference Manual, Rev. 3, 07/2018

1134

NXP Semiconductors

Summary of Contents for Kinetis KE1xZ256














































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Kinetis KE1xZ256

Panasonic FP0 Series Specifications preview
FP0 Series
Brand: Panasonic Pages: 27
Panasonic CZ-64ESMC2 Instruction Manual preview
CZ-64ESMC2
Brand: Panasonic Pages: 78
Panasonic GM1 Series Reference Manual preview
GM1 Series
Brand: Panasonic Pages: 98
NAiS FP0 Series Hardware Manual preview
FP0 Series
Brand: NAiS Pages: 173
Panasonic SL-VGU1-EC Instruction Manual preview
SL-VGU1-EC
Brand: Panasonic Pages: 2
Yudian AI Series Operation Instruction Manual preview
AI Series
Brand: Yudian Pages: 26
HANYOUNG NUX TS500 Manual preview
TS500
Brand: HANYOUNG NUX Pages: 56
YASKAWA Z1000 CIMR-ZU*A Series Programming Manual preview
Z1000 CIMR-ZU*A Series
Brand: YASKAWA Pages: 340
ETC Echoflex ELED2 Installation Manual preview
Echoflex ELED2
Brand: ETC Pages: 8
Texas Instruments MSP430F67681 Manual preview
MSP430F67681
Brand: Texas Instruments Pages: 27
Eaton DCF 800 TWIN Installation And Maintenance preview
DCF 800 TWIN
Brand: Eaton Pages: 2
GCE Druva MTLX Instructions For Use Manual preview
Druva MTLX
Brand: GCE Pages: 46
Tusa RS-790 Owner'S Manual preview
RS-790
Brand: Tusa Pages: 72
Danfoss 080Z0130 Manual preview
080Z0130
Brand: Danfoss Pages: 96
RADEMACHER Troll Comfort Instruction Manual For The Electrical Connection And For Commissioning preview
Troll Comfort
Brand: RADEMACHER Pages: 112
Newport i/8 Quick Start preview
i/8
Brand: Newport Pages: 2
Lattice Semiconductor MachXO5T-NX Quick Start preview
MachXO5T-NX
Brand: Lattice Semiconductor Pages: 2
dunkermotoren ServoTube 25 Instruction Manual preview
ServoTube 25
Brand: dunkermotoren Pages: 34

Brands by name

Popular brands

Load more brands