manualshive.com logo in svg

NXP Semiconductors freescale KV4 Series, Reference Manual

Share
Download
NXP Semiconductors freescale KV4 Series Reference Manual Download Page 816

37.4.46 Software Controlled Output Register (PWMA_SWCOUT)

These bits are double buffered and do not take effect until a FORCE_OUT event occurs
within the appropriate submodule. Reading these bits reads the buffered value and not
necessarily the value currently in effect.

Address: 4003_3000h base + 184h offset = 4003_3184h

Bit

15

14

13

12

11

10

9

8

Read

0

Write

Reset

0

0

0

0

0

0

0

0

Bit

7

6

5

4

3

2

1

0

Read SM3OUT23 SM3OUT45 SM2OUT23 SM2OUT45 SM1OUT23 SM1OUT45 SM0OUT23 SM0OUT45

Write

Reset

0

0

0

0

0

0

0

0

PWMA_SWCOUT field descriptions

Field

Description

15–8

Reserved

This field is reserved.
This read-only field is reserved and always has the value 0.

7

SM3OUT23

Submodule 3 Software Controlled Output 23

This bit is only used when DTSRCSEL[SM3SEL23] is set to 0b10. It allows software control of which
signal is supplied to the deadtime generator of that submodule.

0

A logic 0 is supplied to the deadtime generator of submodule 3 instead of PWM23.

1

A logic 1 is supplied to the deadtime generator of submodule 3 instead of PWM23.

6

SM3OUT45

Submodule 3 Software Controlled Output 45

This bit is only used when DTSRCSEL[SM3SEL45] is set to b10. It allows software control of which signal
is supplied to the deadtime generator of that submodule.

0

A logic 0 is supplied to the deadtime generator of submodule 3 instead of PWM45.

1

A logic 1 is supplied to the deadtime generator of submodule 3 instead of PWM45.

5

SM2OUT23

Submodule 2 Software Controlled Output 23

This bit is only used when DTSRCSEL[SM2SEL23] is set to b10. It allows software control of which signal
is supplied to the deadtime generator of that submodule.

0

A logic 0 is supplied to the deadtime generator of submodule 2 instead of PWM23.

1

A logic 1 is supplied to the deadtime generator of submodule 2 instead of PWM23.

4

SM2OUT45

Submodule 2 Software Controlled Output 45

This bit is only used when DTSRCSEL[SM2SEL45] is set to b10. It allows software control of which signal
is supplied to the deadtime generator of that submodule.

0

A logic 0 is supplied to the deadtime generator of submodule 2 instead of PWM45.

1

A logic 1 is supplied to the deadtime generator of submodule 2 instead of PWM45.

Table continues on the next page...

Memory Map and Registers

KV4x Reference Manual, Rev. 2, 02/2015

816

Preliminary

Freescale Semiconductor, Inc.

Summary of Contents for freescale KV4 Series
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands