Warranty Service
Warranty service must be performed by an authorized service center, usually a NXG speaker
systems dealer or its authorized agent. You may obtain a list
of authorized service centers by contacting NXG. All war-
ranty repairs must be accompanied by the original bill of
sales. No other document is acceptable or is required. This
warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
NXG reserves the right to revise speaker system specifications
without notice.
NXG Speakers Three-Year Limited Warranty
If the NXG speaker system proves to be defective in workmanship or materials within three
years from the date of the original customer’s purchase, we will, at our option, repair or
replace the defective product.
Limitation of Implied Warranties
Any implied warranties, including warranties of merchantability and fitness for a particular
purpose, are limited in duration to the length of this warranty.
Exclusion of Certain Damages
NXG’s liability for any defective product is limited to repair or replacement of the product at
our option.NXG shall not be liable for incidental or consequential damages of any kind or
character because of product defects. Some states do not allow limitations on how long an
implied warranty lasts and/or do not allow the exclusion or limitation of incidental or conse-
quential damages, so the above limitations and exclusions may not apply.
5. Attach the wire to the input terminals on the rear of the
speaker. Remember to maintain proper polarity with the
amplifier by attaching the positive (+) lead to the red ter-
minal and the negative (-) lead to the black terminal.
6. See Fig. 5. With the speaker wire attached to the
speaker, slide the speaker up inside the cut-out hole.
Center the speaker in the cut-out hole and turn the four
locking screws clockwise until the speaker is drawn up
snugly to the wall board from behind, clamping the speak-
er in place. Try to tighten each screw equally. Replace the
speaker grill by gently pressing it into place. If necessary,
use black grille adhesive to secure the grille.
New Construction
1. Determine speaker locations and mark them on your
plans for future reference.
2. If possible, run speaker wires after HVACand electrical
wiring is in place.
3. Secure speaker wires in place along the run with insu-
lated staples only and be careful not to pierce the wire’s
insulation. Allow a bit of slack for expansion of building
materials.
4. Needless to say, the actual speakers should not be
installed until the wall board is in place. In the meantime,
leave several feet of wire coiled up and secured at the
back side of the mounting hole.
5. To complete the installation follow steps 2 through 5
above.
Operational Check
After making all connections it’s a good idea to make sure
every thing is working properly. Turn on your surround or
stereo system making sure the volume control is turned
down and that the balance control is in the center position.
Activate a musical or movie source such as FM, a CD or
DVD player. Gently turn up the volume, you should hear
sound coming from your new NXG speakers. If no sound
is heard from any or all speakers, switch off the system
immediately and check for open or loose connections,
wrong polarity or shorts, or improper source selection.
FIG. 5
16648 North 94th Street
Scottsdale, AZ 85260
1-800-733-0008
www.nxgtech.com
This Warranty Does Not Cover:
• Damage caused by abuse, accident, misuse, negligence, or improper operation.
• Any product whose serial number has been altered, defaced, or removed.
• Products that have been altered or modified.
• Normal wear and maintenance.
• Damages caused by shipping. (All claims for shipping damage must be made with the carrier.)
FIG. 4
(Continued from front)
Input
Connectors
NX-C8.2-ENC-X Specifications
Maximum Power Handling:
5 - 80 watts
Sensitivity:
90dB @ 1 watt/1 meter
Frequency Response:
55 Hz-20,000 Hz
Driver Complement:
8˝ (203mm) mica-filled polylaminate cone woofer with rubber surround
1
/
2
˝ (13mm) zero-diffraction pivoting, liquid-cooled titanium anodized dome tweeter
Nominal Impedance:
8 ohms
Overall Dimensions:
11˝ (diameter) round x 7˝ D (279mm x 178mm)
Required Ceiling Cutout:
9
5
/
8
˝ (diameter) round (244mm)
