manualshive.com logo in svg

NW Explorations Navigator, Operating Manual, Page: 19 / 58

Share
Download
NW Explorations Navigator Operating Manual Download Page 19

NW Explorations  

NAVIGATOR OPERATING MANUAL

 | 

17

Section 4: Specific Boat Systems & Operations

This section of the operating manual will discuss each of the boat’s systems.  The systems and major 

components discussed are in alphabetical order as follows:

4A: Anchor & Ground Tackle
4B: Barbeque
4C: Bilge Blowers
4D: Bilge Pumps
4E: Dinghy, Davit & Outboard
4F: Electrical Systems, AC
4G: Electrical System, DC
4H:  Electronics
4J: Engines & Transmissions

4K: Fresh & Waste Water Systems
4L Fuel System
4M: Furnace
4N: Galley & Appliances
4P: Head Systems
4Q: Running Gear (Props, Shafts, Thruster)
4R: Safety Equipment
4S: Sea Strainers & Thru Hulls
4T: Warning Lights, Alarms & Wipers

4A: Anchor & Ground Tackle

4A1:  Anchor Bridle

There is an anchor bridle stowed forward on the boat in the deck storage box.  Use it when anchoring overnight, 

as it accomplishes three goals:

•  It takes the strain of the anchor off the windlass, pulpit, and pulpit pulley and directs it to the bow cleats 

which are more suited to hold it;

•  It reduces substantially the “chain noise” transmitted to the occupants of the forward cabin;

•  It allows the anchor rode to have a lower angle relative to the sea bottom, thus increasing the anchor’s 

holding power.

To use the bridle:

1. 

Lower the anchor normally (see page 4.2) then, after it is set,

2. 

Hook the bridle on the chain just in front of the anchor pulpit bow roller;

3. 

Then secure the bridle rope ends through the side-coaming hawse pipes, to the bow cleat on each side 

so the bridle lines are equal in length and as long as possible;

4. 

Last, operate the windlass to pay out anchor chain so the chain slacks and is supported by the bridle, 

the chain forming a loop right in front of the boat’s bow.

If you wish, you can pay out additional chain to form a long hanging loop between the boat and bridle, which 

weights the chain down in front of the boat well below its normal path; thus the chain itself becomes a “kellet” or 

“sentinel”, lowering the chain angle more than the bridle alone.  The weight “drooping” the chain down like this 

then forms a an even more effective “snubber”, so the boat is gently held against the pressures if wind and tide.

Summary of Contents for Navigator



























































Reviews:

No comments