background image

NV8288 and NV8288-Plus Digital Video Routers • User’s Guide

13

2. Introduction

Module Slots and Rear Connectors

Config. However, UniConfig is also run on a PC and similarly cannot communicate with the router 
until an IP address is entered. Therefore, a connection to the PC running UniConfig needs to be cre-
ated using a serial connection: serial. (See 

Serial Control Connections

 on page 38.) 

Figure 2-10. Ethernet Connections to Router Control System (Rear View)

Control System Expansion Connections

In order to manage two connected NV8288-Plus routers, control system expansion connections 
need to be connected between the routers. Expansion control system connections are located on the 
rear of the router, as shown in Figure 2-11.

When making control system connections, only one router is directly to the control system. This 
router acts as the 

primary 

router. When making control system expansion connections, connections 

from the remaining router, the 

secondary

 router, are made to the 

primary

 router. This enables the 

router control system to communicate with both routers through the primary router.

There are two control system expansion connections, labeled ‘RTR Expansion’. The ports are 
divided into two sets, one primary (‘PRI CTRL’) and one secondary (‘SEC CTRL’). Primary con-
trol is the connection to the primary control card. Secondary control is the connection to the sec-
ondary (optional for redundancy) control card. One port is for 

primary

 control (‘PRI CTRL’), 

connecting the local router to the control system.

For instructions on making control system expansion connections, see 

Control System Expansion 

Connections

 on page 40. 

Figure 2-11. Expansion Control System Connections (Rear View)

Diagnostic Connections

The diagnostic connections enable the router to communicate with the UniConfig application. Uni-
Config runs on a PC separate from the router and is used to perform system setup tasks, and config-
ure and monitor the router. (See 

Configuration

 on page 51.) For information about using 

UniConfig, see the UniConfig User’s Guide. 

Diagnostic connections connect the router to the PC running the UniConfig application. Two diag-
nostic connections are located on the rear of the router, labeled ‘DIAG’. The ports are divided into 
two sets: one primary (‘PRI CTRL’) and one secondary (‘SEC CTRL’), as shown in Figure 2-12. 
The primary control connects to the primary control card. The secondary control connects to the 
secondary (optional for redundancy) control card.

RTR EXPANSION

E146905

10/100 BT

10/100 BT

RTR EXPANSION

VIDEO

REF 1

LOOP

VIDEO

REF 2

LOOP

AUX 1

AUX 2

CTRL 1

CTRL 1

CTRL 2

CTRL 2

ALARMS

POWER SUPPLY

MONITORS

POWER INPUT

TIME

CODE

PRI

CTRL

SEC

CTRL

PRI CTRL

SEC CTRL

DIAG (38.4 Kbaud)

DIAG (38.4 Kbaud)

Ethernet Connections 

to Router Control System

RTR EXPANSION

E146905

10/100 BT

10/100 BT

RTR EXPANSION

VIDEO

REF 1

LOOP

VIDEO

REF 2

LOOP

AUX 1

AUX 2

CTRL 1

CTRL 1

CTRL 2

CTRL 2

ALARMS

POWER SUPPLY

MONITORS

POWER INPUT

TIME

CODE

PRI

CTRL

SEC

CTRL

PRI CTRL

SEC CTRL

DIAG (38.4 Kbaud)

DIAG (38.4 Kbaud)

Expansion Connections 

to Other Router

Summary of Contents for NV8288























































































Reviews: